30531 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》강남하이킥레깅스룸Χぬscheme하이킥레깅스룸⊂선릉하이킥강남하이킥레깅스룸⑪も강남하이킥they 강남하이킥레깅스룸㈌선릉하이킥ㅼぷpoor"

The actual informations
Log from Extension card for TDS3000 scopes
Detecting and identifying a card As stated in an earlier log, the card insertion is detected by grounding the pin *CD. But this is not enough to make the scope believe he have a know card inside him. You need to indicate him what type of card was inserted....

My own try at a RingO9 with 2N2369A
Log from Hackaday TTLers
Edit: See also More 2369, with more caps !With a sporadic and limited access to the workshop (at last !) I can finally try new ideas ! I have meanwhile received 9K PMBT2369 in SMD but I decided to use the old stock of 50pc 2N2369A in metal can, that...

Top 100 Projects by Comments
Log from Statistics for 2015 Hackaday Prize Entries
Place View Count Followers Comments Skulls Project Author 1 48300 273 112 120 Luka EV MW Motors 2 61900 273 85 98 EM-Drive movax 3 23500 245 73 106 ARDUINO MPPT SOLAR CHARGE CONTROLLER Debasish Dutta 4 18600 149 64 67 SubPos - Positioning System Blecky...

AD5522 eval board setup and first tests
Log from Poor men's PMU
I completed first tests with the development board after avoiding a SPI driver problem. I did use the board now to measure some diodes. I am using python notebooks on a Raspberry to combine measurement with the AD5522 with plotting of the data. Details...

It's Finished
Log from Not another D'Arsonval Movement clock
Sorry for the long delay in finishing up this blog. But the project is finally finished.I will be adding some additional photos and uploading the source code to Github.At the end of the day it turned out ok, I need to replace the seconds meter and look...

Calibration
Log from Poor men's PMU
In part 4 of my journey with the AD5522 evaluation board I now focused on the calibration of the board to get better accuracy. Afterwards I did show measurement accuracy up to a few nA by measuring the photo-sensitivity of the some selected LEDs.Find...

cymk, and poor temp resolution
Log from Arcus-3D-M1 - Full Color Filament Printer
I did some tests of the 555 timer based temp feedback. The resolution at operating temperature was poor ~7 degrees. The resolution at room temperature was a lot worse ~30 degrees. The refresh rate was also poor. Seems the sensor chip was outputting at...

Seeing the Light with RPLIDAR
Log from OSCAR: Omni Service Cooperative Assistant Robot
Good news everyone (in Professor Farnsworth's voice)! The first of our navigation sensor the RPLIDAR has arrived. We gotten ours from Seeedstudio for a little under 400 bucks. For those who are not familiar with the RPLIDAR, it is probably one of the...

ESP8266 and MQTT Stability
Log from NeoPixel Temperature Display
Currently testing MQTT stability on an ESP8266 running the LUA firmware. The data then gets JSON formatted and sent out the serial port to the ATmega328p. The stability is poor right now so it doesn't last long before hanging up. Therefore no longer...

Blocks, Name Tag, Guitar tests.
Log from Shapeoko 3
I finally finished the name tag that came with my cat tree.Also tried to cut some OGEL blocks but poor alignment and lack of homing didnt help. Time for limit switches!I also ended up trying some 3d stuff, again a super long video, mainly because I was...

Improve accuracy
Log from D.I.M.E.R PROJECT 6 DOF Robot Arm
On previous video you can see that the accuracy is very poor, so i'm working now on it.I think that the problems is the shoulder (becasue i use ropes to transmit motion). I need to change it to gt belt and improve the movement of the motor shaft.[25-4-16]...

Week 9
Log from F3Dew
During this week, we glue some pieces of wood between the pillars, all around the main structure and graph plastic bags in it, to make the water fall. It was long because the glue toke 10min making effect, and we made 6 levels of bags and strengthening....

Basic design finalized- Prototype 1
Log from Mechanical Laser Show
I decided on the final layout I ended up pursuing. Here was my first prototype that I actually modeled and printed. For the cam design, I made a single set of cams manually by hand once before I created the software. I made the assumption that the angle...

We are outside wherever now!
Log from Bin Temperature Monitoring System
Hey! I have made an enclosure for the Arduino. Before this enclosure I just left the Arduino in a BBQ to see how long it would work on the solar panel. I also am using a more powerful solar panel. Right now I am mostly testing whether or not the poor...

Startup.
Log from Using an Allegro A4979 stepper motor control devel
Unboxing shows a PCB and a CDROM.Plug in the CDROM and I get a "READMEFIRST.TXT" file that says:1) Click on Setup...2) Then plug in the USB cable.USB CABLE???? For a stepper motor driver?Well, they have some really poor GUI for click-n-test that has...

1
2
3
4
5
>
>|