Close

31100 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》선릉레깅스룸㉹ベgrace레깅스룸S선릉레깅스룸선릉레깅스е я레깅스룸비용superstition 강남레깅스룸′강남레깅스§8fetch"

  • Tablet Init

  • We have some bytes from the tablet. It's all pretty standard stuff with one exception.// unenc init a4 w f0 55 a4 w fb 00 Read ID Bytes a4 w fa a5 r ff 00 a4 20 00 13 // Enter enc mode a4 w f0 aa // write 16 byte key a4 w 40 e0 7d e0 7d e0 7d a4 w 46...
  • Tinymovr

  • Found out about the Tinymovr motor controller. Basically what I'm trying to do! Very cool, and my version 2 will use it as reference. I hope to make mine even smaller (27x27mm vs 40x36mm) and cheaper ($40 vs €89). I only need up to 13V (3S lipo),...
  • Frequencies

  • For some reason the 47 pF value for the caps is sitting in my mind. Either after 'calibration' the LC meter is so far off that it read both my TI-89's and my V200's caps 51 pf, both ~8% high, or both of them are within their 10% tolerance and reading...
  • Parity with Fibonacci

  • One thing that sets PEAC apart from the Fibonacci and Pisano series is the parity, or mod 2 remainder. When you take the natural sequence 0, 1, 1, 2, 3, 5, 8, 13, 21, 34, 55, 89, 144, 233, 377, 610, 987, 1597... The mod 2 is 0, 1, 1, 0, 1, 1, 0, 1, 1,...
  • Z80 (CP/M) Writing to SD Card

  • Digging into SD card writes means shifting gears from the Boot BIOS source code since the Boot BIOS code only does reads. The CP/M BIOS code (CBIOS128.LST) which does the reads/writes after booting. Here's the BIOS code for writes to the SD Card: 0754...
  • Finally, some publicity!

  • An article recently published on MOONGIFT, a Japanese developer site, has showcased RasDash! The article is entirely in Japanese and Google Translate won't accept the URL as it has special characters but YANDEX does. Below are some links and a basic...
  • No officer, it's not a bong. I swear.

  • Morning update: April 13, 89 PDAfter a long night of fighting with 123D make and my 3d printer, we have our first put together. To see very bad pictures of the Main Power/Data Bus (MPDB) look at step 2 of the instructions. After getting put together,...
  • It's like being in college again.

  • Mid-day update: April 20, 89 PDWhile over 75% of the internal parts are finished printing, but there is still too much to do. We have started wiring up the reactor with LEDs but it is slow going (25% done). We have not even started on the code to drive...
  • MORE RADII!!

  • I haven't putzed about with the v0.1 base at all, but I think I've got a motor mount design that I like. It's got the split bolt setup for securing the motor (including a cutout for holding a 2-56 nut), and the legs are cool lofted dealies. Lots of radii...
  • Fibonacci

  • With the ALU verified and the RAM connected, today the breadboard determined that the first 8-bit Fibonacci number is 144. 0000 0000 ld $00 ; outer loop 0001 c200 st [$00] ; a=0 0002 0001 ld $01 ; b=1 0003 fc0a bra $0a 0004 0200 nop ; (pipelining) 0005...
  • Log #89 - CondomBoard specifications

  • Size: about 50x50mm (size of condoms I have, could be a little larger if required)Layers: preferrably a single 2-layer PCB, for easier ordering at the usual suspects in ChinaConnections: debug UARTMicroUSB for charging the batterytemperature sensor connectortwo...