657 Results for "solder fume extractor"

Solder the Pi Zero onto the back board
Instructions from ZeroPhone - a Raspberry Pi smartphone
The Pi Zero has to be soldered onto the back board pin header. You also need to use small bits of wire to attach the Pi Zero USB data line testpoints to corresponding pads on the back board.This is an almost-irreversible operation. Before you solder...

Bend the brass rod and solder the end
Instructions from Freeform tree of life with LED's
Use the template to bend the brass rod It helps to use a round object as follows: I used a small piece of double sided tape to keep the open ends together before soldering. Applying flux before soldering makes it easier to join both sides.

BUILD
Instructions from WiFi cracker ESP8266(PBC)
It is a simple circuit you don't have to follow what i have did.But this is what i did take a piece of perf board solder 7 headers to it then take some bare copper wire and make a ground pad on the solder side of perf board for coin cell where then...

Evaluate your PCB surface mount soldering/reflow equipment
Instructions from TinyFPGA A-Series
The FPGA for these boards is in a QFN32 package which is possible, but very difficult to solder with an iron. It is much easier to use the solder paste reflow method to assemble these boards.The following tools and supplies will be necessary to reflow...

TeensieWI woodwind USB MIDI controller
Instructions from TeensieWI woodwind USB MIDI controller
For connecting electrodes, solder small pieces of copper tape onto the stripped ends (4mm) of regular insulated copper wire for electronics. This is done very easily if you solder onto a longer piece of tape that is cut after the soldering.

LED Wiring
Instructions from Pentesting BBU Dropbox
Next we'll wire up the LED. You'll need the 470 ohm (yellow, violet, brown) or similar resistor, the LED, two lengths of wire, and (optionally) a connector that will plug into the Pi's GPIO. Solder the red wire to the positive lead on the LED & heat...

PixiFlood
Instructions from PixiFlood
STAGE 1 ASSEMBLY:Solder: PT4115BE89 (3) to PCB. Use VERY LITTLE SOLDER ! A fine gauge solder would be helpful and check for bridged solder joints before applying power to the board. There are several tutorials on "Drag" soldering of SMT components available...

Raspberry Pi 3 Gameboy
Instructions from Raspberry Pi 3 Gameboy
11. Adding shoulder buttonsSolder 2 tactile switches to a small piece of perfboard, and then make another one for the other side. These will be the L1, L2, R1 and R2 switches. Afterwards, drill the holes and glue them in your desired position and solder...

Tues 12-11 Progress Log
Log from Induction Heater
What got done: Soldered in Zener diodes, power resistors, 10K resistorsConnected MOSFETs to central negative railCreated heavily-soldered rail for each MOSFET connection to positiveAdded solder to board to buik up positive rail Issues: Difficult to connect...

ESP-12 (ESP8266) Pogo Jig
Details from ESP-12 (ESP8266) Pogo Jig
BOM -2 x cheap "esp-12 adapter" white boards16 x pogo pinspin headersa piece of FR4 one-sided boarddouble-sided proto board (off the shelf part)kapton tapeSteps to create -First board:desolder the resistors on the bottom of the boardstick kapton tape...

Add a wire to the motor side
Instructions from Tiller Autopilot Limit Switches
The switch with the roller (outboard side) now needs to get a wire that goes to the motor. You can either solder a short piece of wire onto this lug with a spade connector (M) male to mate with the motor wire's spade (F) female or cut off the motor wire's...

Logic Noise: Klangorium
Instructions from Logic Noise: Klangorium
First, put all the header pins in their respective holes. Now get a piece of cardboard and put it on top of the pins before you (gently) flip it over. This way, you stand a chance of getting the pins aligned straight with the board upside-down. Now solder...

Blink Coin cell toys collection
Details from Blink Coin cell toys collection
Check in store I want to teach kids about the technology we had before self-flashing LEDs :) It not using obviously self-flashing led but old good astable multivibrator. It is a nice piece of old fashion technology.1206 components are easy to solder...

RGB LED Strip Controller Circuit
Details from RGB LED Strip Controller Circuit
➢Step descriptions: ✦Step 1:-Prepare all the part need in this videos: 8050 transistor X3, 220uF capacitor 8*10mm X3, 10k resistor 0.5W X3, RGB strip DC 12V X1 and Some wire jumpers ✦Step 2: -Solder all the transistors, capacitors and resistors...

Circuit Board
Instructions from 555 LED Bicycle Indicators
Follow the Circuit Schematic and solder the circuit together as shown in the pictures. The Components section below details the required components and specifications of which of each electronic component to get, as well as the hardware used while creating...

|<
<
1
2
3
4
5
>
>|