Close

3995 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》레깅스룸견적よ레깅스룸ago레깅스룸メ강남레깅스룸eighty 선릉레깅스룸κ선릉레깅스⒲레깅스룸メｃ선릉레깅스룸literary"

  • Portable environmental monitor
  • Instructions     from Portable environmental monitor
  • Populate the board. You will need some good experience with 0805 SMD soldering, and some tools like soldering iron and hot air rework station. Start with the bottom side, with the microcontroller, the other ICs and finally the small passive components....

  • Cree Dimming Level
  • Instructions     from Cree Dimming Level
  • Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

  • Arduino-Compatible FPGA Shield
  • Instructions     from Arduino-Compatible FPGA Shield
  • Step 2 - Import the Arduino board file into Altium Designer:  Using Altium Designer (AD) requires that I import Eagle board into AD.  AD14.x includes an Eagle importer.  Used source files from the Arduino site to import in AD.  

  • Arduino-Compatible FPGA Shield
  • Instructions     from Arduino-Compatible FPGA Shield
  • Step 3 - Build major footprints:  Costing the available board area requires building the major footprints and placing them on the PCB.  Built early footprints and placed to determine what additional space is avail.  Files in git.

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • Unscrew the circuit board and pull off the RF shield. Be carefull because once you take the board out there will be nothing holding the buttons in.

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • Carefully bend the EL panel leads so they fold around the back of the PCB. The panel can bend pretty far, just don't crease it.Now install the board back in the front half of the case and screw it down. The EL panel leads will stick up through gap between...

  • Wearable computer
  • Instructions     from Wearable computer
  • Disassemble the primary unit of the video glasses, which now resembles a black plastic bar. You should end up with two boards connected by a thin-film ribbon cable, one of which is connected to another board (containing a USB-like plug) connected by...

  • Wearable computer
  • Instructions     from Wearable computer
  • The board with the USB-like connector on it will be connected to the colored wires via surface-mount solder on top of vias. This is a really bad thing for the kind of torque you are likely to put on this connector board. So, desolder these wires using...

  • Wearable computer
  • Instructions     from Wearable computer
  • Unscrew one of the threaded caps on the goggles and remove the clear plastic pane. (Your pair may have a silvered or coloured glass pane on top; if so, remove this as well but do not drill into it -- discard it or keep it as backup for the other side.)In...

  • Wearable computer
  • Instructions     from Wearable computer
  • On the board containing the USB-like connector, on the edge opposite the connector whose wires you have resoldered, fold a piece of velcro. Connect the connector and then position a piece of velcro of the opposite type on top of your mask based on where...

  • Wearable computer
  • Instructions     from Wearable computer
  • Disassemble the primary unit of the video glasses, which now resembles a black plastic bar. You should end up with two boards connected by a thin-film ribbon cable, one of which is connected to another board (containing a USB-like plug) connected by...

  • CUBEX
  • Instructions     from CUBEX
  • Download and build board files: https://github.com/arkorobotics/CUBEX_V1/tree/master/Board

  • CUBEX
  • Instructions     from CUBEX
  • Order CUBEX BOM: https://github.com/arkorobotics/CUBEX_V1/blob/master/Board/BOM.xlsx
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday