1495 Results for "3D printing"

Hotglue USB jack to the enclosure
Instructions from $20 USB MIDI host
If you're using my 3D-printed case, USB jack hole located is too low, so in order for it to not bump into the Pi Zero I decided to hotglue it upside down.

KiCad Setup
Instructions from KAN-15 LED Tactile Switch
If you use KiCad, download and add my KiCad library so you have access to all the prebuilt footprints and 3D models.https://github.com/jgillick/KiCad-librarySMD: SW_KAN-15_SMDThrough hole: SW_KAN-15_PTH

3D Print a Sound Wave
Instructions from 3D Print a Sound Wave
I exported the .stl file and loaded it into the 3D printer and voila! I hold the spoken word.

Electronics/Finishing - Step 9
Instructions from MiniHawk VTOL
Perform any other measures necessary to get the vehicle ready for flight. Decals, paint, or heat-activated covering are possibilities. Vehicle mass should come to an All-Up-Weight around 700 grams to 800 grams, with the 3D-printed airframe alone measuring...

Components and materials
Instructions from CanAirIO Bike
Please first review the last updated list of components and 3D Printer files here

Print the case
Instructions from Multi VC Mute Button
Print the components. I used transparent for the buttons and the knob for the neopixels to shine through and black for the case. It worked well as the black doesnt allow the light to pass through.

getting the files.
Instructions from Pocket NC jog controller
go to my GitHub page and download all the files: https://github.com/George0023/pocket-nc-jog-controller 3D print the stl file in sequence.

Nod Servo Installation
Instructions from 3-Axis Skull Mod for 12ft Skeleton
Still using the 2nd level (red) 3D printed part. Install the servo arm shown (you may need to remove and adjust its position later on).Position the Nod servo as shown and attach with the included hardware.

Braille Cell cap and pins
Instructions from Thenar - portable and affordable Braille book
Braille pins and pin cap is better to print on an LCD 3d printer. However you can print on FFF printer, and it will need more sanding and drilling cap holes for pins.

List of equipments and tools you need to make Thenar.
Instructions from Thenar - portable and affordable Braille book
hot glue gunpaint brushes (1” and 3”)screwdriver setArduinosoldering ironwire cutterdigital multimetermetal file(s)sanding block3D printertool box

Hand tools and fabrication machines:
Instructions from UV Sanitizing Autonomous Robot
3D PrinterDigital MultimeterSmartphone AndroidSoldering ironHot glue gunAluminum foil Female/Male Extension Jumper WiresPlastic cable tiesWorking tools: screwdriver, screws, nuts

***************** INJECTION MOULDING ***********************************
Instructions from 3D Printing and Moulding with Recycled Facemasks
The following steps cover the process of injection Moulding LFD test cases using 3D printed mould tools and recycled facemasks. Step 1 from above is required to produce pellets for use with the injection moulding machine.

Make a base
Instructions from Wooden Christmas tree with addressable LEDs
I 3d printed a base to keep the Christmas tree up. You can find the STL under the files section.

Assemble the component
Instructions from The Fuxk Button | Best DIY Tool for Linux Beginner
3D print the case and base then use hot glue to secure both the encoder and the BW16 dev board to the base, connect pin 8 of BW16 board to the encoder switch pin and Vcc to encoder's GND

Fillets
Instructions from 100% reusable electronics
3D models created for realistic visualization often have a lot of unnecessary details. Some also have rounded corners like for capacitors and resistors. These must be removed because you want sharp edges to make contact with the PCB so that when doing...

|<
<
50
51
52
53
54
>
>|