1804 Results for "Q%20%EC%95%88%EC%82%B0%EB%B8%94%EB%9E%99%EC%9E%AD%20CDDC7_C%D0%9EM%20%E2%97%86%EB%B3%B4%EB%84%88%EC%8A%A4%EB%B2%88%ED%98%B8%20B77%E2%97%86%EC%88%98%EC%9B%90%EC%9E%A5%EC%95%88%20%ED%94%84%EB%A1%9C%ED%86%A0%20%EA%B5%AC%EB%A7%A4%E0%B9%8F%ED%86%A0%ED%86%A0%ED%95%AB%ED%94%BD%E2%8F%AC%EC%98%A8%EB%9D%BC%EC%9D%B8%ED%99%A9%EA%B8%88%EC%84%B1%E0%BC%88FX%EB%A7%A4%EB%A7%A4%E2%8B%8D%EC%95%88%EC%82%B0%EB%B8%94%EB%9E%99%EC%9E%AD%EC%95%A0%EC%9A%A9%20thorough/"

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

Comparison Between RFM95/96/97/98
Instructions from LoRa RFM98 Tutorial Ra-02 HopeRF module comparison
The main difference between the RFM modules is that they operate on different frequencies. As all the countries do not support the use of the same frequency band for free you need to used different module in different country. You can find about...

1 - Take an A4 paper
Instructions from Covid 19 washable origami mask

Trying out GATTTOOL
Instructions from Reading a bunch of BLE sensors with raspberryZero
Now that i know how to access and decode the data lets try the Raspi GATTTOOL default BLE handler:Native to Debian and a lso to a bunch of linux distros or so i've heard of . First i reset the bluetooth of the raspi, just in case: sudo service bluetooth...

Step 20
Instructions from DIY Decorative lamp | Home Decor Ideas
Open Shape Generator Turn Off "Hide all objects" Set Top and Bottom radius to 28 Number of Edges set to 64 Height set to 10

Cree Dimming Level
Instructions from Cree Dimming Level
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

Raspberry Pi Zero Smart Glass
Instructions from Raspberry Pi Zero Smart Glass
Step2: Pop out the Lenses

Some notes
Instructions from Hydroponics Sensor
The ESP-32 board pins operate in 3.3v levels while the Gravity pH and EC sensors operate in 5V. I inserted a simple voltage divider to shift 5v to 3.3v levels on the signal pins.

Make 20 vactrols
Instructions from PHOSPHOR Video Distortion
In order to control the video effects via MIDI, I needed a part that could override the potentiometers. For full effects, I need less than 30 ohms, to switch an effect off completely, a resistance of more than a few kohms would be desirable. I couldn't...

LK-99 Synthesis Instructions
Instructions from LK99 Synthesis attempts
Below are the instructions given by the original lab that claimed to produce the room-temperature superconductor LK-99:- Prepare lanarkite (Pb2SO5) - PbO and PbSO4 mixed uniformly in a 1:1 molar ratio - bake in a...

Arty a7-100t full release.
Instructions from Merlin
Load the .bit file onto your Arty using Vivado. When the monitor starts, press L, then load the firmware s-record via your favourite terminal https://github.com/mattuna15/zed-68k/releases/tag/ARTY-100T-v1.0

Connect pin A0 to pin 11 on the Arduino board and click Acquire on the Arduscope web interface.
Instructions from Arduino oscilloscope with a web interface
You should see the 500Hz calibration signal displayed.

LK-99 Synthesis First Trial
Instructions from LK99 Synthesis attempts
Below are the steps that our lab followed during the first attempt of recreating LK-99:- Prepare lanarkite - weigh out roughly 1.7g PbO and 2.3g PbSO4 - mix until uniform in a clean beaker - transfer...

Step 20: Gather components for sub-sea cable
Instructions from "Mercator Origins": Sat Nav & Telemetry for Divers
Components: Blue Robotics 4-core Ping Cable (11 metres), 2 x 4.5mm WLP-M06 cable wet link penetrators including nuts, o-rings, and silicone seal, plus 2 x cut shake-proof washers, 1 x rubber strain relief boot , 2 x Micro JST 2-way female connectors....

CURA Slicer for the Recore, PrintrBot Simple Metal 1403, and Refactor, and now a Maker Select Plus w/ Recore A7!
Instructions from Recore and PrintrBot Mixtures
Hello...I have made the PrintrBot 1403 w/ a bed of 19.75" * 19.75" * 6" from a six inched cubed build environment. Now, that I am done w/ building that overweight beast of a printer, I have sort of moved on to a Monoprice Maker Select Plus...Since sort...

1
2
3
4
5
>
>|