5826 Results for "X 올림피크 리옹 CDDC7닷컴 ㅿ프로모션번호 B77ㅿbepickڸ원엑스벳 슬롯머신ಣ서천복권방ṓ한화이글스오늘경기ୀ올림피크 리옹사랑 backpedal/"

Megaman X - Super Famicade Edition
Log from Super Famicade - Hardcore SNES Arcade Hack
So... I started poking through the ROM for Megaman X (V1.1) and noticed some copy protection. Some key points:Some of the copy protection routines check for SRAM and will aggressively screw with the game when it is detected.The original MMX cartridge...

Chapter 3 - Adaptator X, Electronics
Log from Adaptator X and the chamber of Pickle-Rick
Once the basis of the Adaptator X was created, an electronic system was added to control the rise level of the horizontal bar holding the phone. The main board was pierced, and a flexible camera tripod was fixed to it with screw and bolt.An Arduino Leonardo...

Testing CNC X Axis Motors
Log from WEEDINATOR 2019
The WEEDINATOR, if you did not know already, is an autonomous roving CNC machine that travels around a farm weeding beds of vegetables. The actual weeding mechanism is similar to a woodworking router, but acts on soil not wood.I tested the X axis motors...

[M] X Axis Slider Concept
Log from SecSavr Sublime [gd0036]
My first guess for the length of the slider was 160mm and it looks to be a good one. I first tried going around, but that looked to take up too much X space, so I rearranged it:Now looking at it again, I could rotate the slider 90 degrees....

Can I use X sensor?
Log from CarbOnBal
I just got an interesting question.Can I use X sensor?The answer depends on three basic properties;1 you need a 1 Bar sensor for best accuracy2 it must operate at 5V and produce a voltage swinging from as low as possible to as close as possible...

From 10 x 8x8 LEDs to 40 x 16 LEDs
Log from Club Matrix
So this took me a while. The library that I'm using stores the matrix data in a one dimensional array with the length of 40 * 16. Each LED matrix is 8x8 and are connected in that order: 0 - 1 - 2 - 3 - 4 | 9 - 8 - 7 - 6 - 5 And each LED...

The new x-axis with bearing..
Log from I**A-CNC Machine
I'm currently building the new X-Axis train with additional bearing.. see below progress :)

BASIC Environment for Mac OS X
Log from Square Inch To Space
...now available in the LINK section. Many thanx to JackPearse (Baltobor)

Replace X/Y motors by bigger one
Log from Big 3d printer upgrade

X-PC 2, Second Prototype.
Log from The X-PC. Hackaday Prize 2022 Entry
I've been given about 30 HP550 laptops. These are old and battered and perfect for turning into new X-PCs! I also wanted to test my FreeCAD model with another laptop, to make sure everything works as it should. I stripped down one the laptops, removed...

[R] 2.4 x 1.2 x 2m Tent Discovery
Log from TrueTent TempLab [gd0143]
[23 - 25 Feb] So this is the first tent in my budget I found on 23 Feb, 23:00: This is a very cool but very expensive tent: This is a cheaper tent that looks more professional: Then I spent 2-3 hours researching about ventilation (which I'll talk...

Completed X,Y and Z
Log from Laser Cut Mini Mill
I finished assembling the Z carriage, I had to reduce the flange on the anti backlash nut for the Z axis to fit the space in the carriage. Mounted a temporary end stop for the Z axis, it limits the travel a little bit but it will work until I can...

Chapter 2 - Adaptator X, Materials
Log from Adaptator X and the chamber of Pickle-Rick
First part of the microscope adaptator consisted of planning the strucure of it and cutting the parts.Our adaptator consisted of a main board, cutted in a particular way in order to fix the moving parts. The moving parts are small elongated pieces allowing...

[X] AirBerries: ZEV-XS Layout
Log from Tetent [gd0090]
ZEV-XSOther than swapping the location of [q/Q] and ['/"], the layout has been mostly unchanged. After 3 hours of Keybr.com and some rounds of Typing Attack, this is what my raw data looks like:I'm not really sure how it counts the number of keys, nor...

X Axis Build Part 1
Log from 3D Printer
Moving on to the X Axis. This axis will use the same printer/mechanism that was used for the claw machine build. It did start with the intentions of using the complete assembly, but later morphed into using only the carriage, belt, and motor combination....

|<
<
5
6
7
8
9
>
>|