166 Results for "soil+sensor"

IMU sensor
Instructions from RAPTA - Autonomous Humanoid Leg
A Mindsensors AbsoluteIMU sensor is attached below the two yellow stoppers just behind the ultrasonic sensor with the X axis pointing in the direction of the sensor, as shown in the camera picture below.

Gesture Sensor Operating Plane
Instructions from MicroMote: The ESP-Now Based Gesture Remote
The gesture operation distance is 15 to 30 cm, the farthest cannot exceed 35 cm. Based on Sensor FOV 78.3° (horizontal) and 62.9°(vertical), and the operating area is 48 x 36 cm² at 30 cm. In addition to the distance to the sensor, you...

Hardware of the sensor
Instructions from Non-contact touch panel
Main board Main board pinout (JP1) pin numberPIN nameexplanation1+5VVcc 5V2GNDGND3ASensor channel 0bit4BSensor channel 1bit5CSensor channel 2bit6SSSPI Slave-Select (active-Low) Substrate selection when connecting in parallel.7MOSISPI Input8MISOSPI Output...

Make the Sensor Mount
Instructions from Seismometer
(This photo is the homemade sensor, but the mounting method described should not change) Front view of sensor mount. Detail of sensor mount attachment. Cut two pieces of 1/8" aluminum plate: 2.5" x 4" and 4" x 4.5".Using the 3/4" copper U-hangers as...

Nine Functions of Gyro Sensor
Instructions from How to Use Gyro Sensor MPU6050 with "skiiiD"
getAccelX() - Get Acceleration value of X-axis getAccelY() - Get Acceleration value of Y-axis getAccelZ() - Get Acceleration value of Z-axis getGyroX() - Get Gyro value of X-axis getGyroY() - Get Gyro value of Y-axis getGyroZ() - Get Gyro value of Z-axis...

Sensor pod from Log 1
Instructions from Hacker Calculus
For the sensor pod introduced in Log 1: First obtain the battery and Adafruit Circuit Playground boards (as noted in the Components section.) Next, if you have never programmed an Arduino before, you will need to download the Arduino IDE (Integrated...

Step 28: Drill hole for depth sensor
Instructions from "Mercator Origins": Sat Nav & Telemetry for Divers
Drill a 10mm hole (recommend using a stepped drill bit) at a position 20mm x 20mm from the top and left sides of the door of the enclosure, viewed from the back. Drill from the outside of the enclosure to the inside. (Photo taken later in the build process,...

Technical Specifications and Applications of the Sensor
Instructions from Capacitive Fingerprint Sensor with Arduino and ESP
The Technical Specifications of this Sensor are as given below:- Operating Voltage: 3.3V Operating Current:

The sensor box central component setup
Instructions from Crop Water Stress Sensor
Let's start with the insides of the sensor box: Screw the 8 6mm screws into the support frame: Then add 6 regular 5mm spacers and two with the screw end to the other side of the support frame: Add the solar power management unit to the left side of the...

NodeRed, connect and display a single sensor
Instructions from Reading a bunch of BLE sensors with raspberryZero
Im 100% sure this can be done better but this is what i have now:I am using an "exec node" feeding a "function" node java-ing the bytes to finally end at different "chart nodes" EXEC node executes a bash script:Connects to the sensor, writes to its configuration...

Creating the wires to connect the sensor with the D1 Mini
Instructions from SMS Garage Alert system using an Ultrasonic sensor
The D1 mini is a cheap microcontroller with a wifi module. It's possible to connect the board with my home Wifi, if I place it next to one of the windows of my garage. The connected Ultrasonic sensor itself has to be placed in front of the garage door...

Installing an ARHS sensor using the MPU9250 that ships with the different ChipIDs regularly
Instructions from Stratux ADSB Receiver and AHRS
When one buys a new MPU9250 module that also comes with a BMP280 pressure sensor from Amazon nowadays the WHO_AM_I chip ID located at i2c register address 0x75 is also 0x75. In older versions this was either 0x71. This is an issue since Stratux only...

Vinduino, a wine grower's water saving project
Instructions from Vinduino, a wine grower's water saving project
Make a gypsum soil moisture sensorComponents needed for one sensor:2 x stainless steel machine screws, 6 - 32 x 26 x stainless steel hex machine nuts, 6 - 321 x piece of window screen glass fiber mesh (5 x 10 cm)1 x plastic spreader (1.5 x 2.75 cm),...

Arduino GPRS IOT Weather Station
Instructions from Arduino GPRS IOT Weather Station
Arduino Soil Probe Using DS18B20 and DIY Moisture Hardware:As a fanatical gardener or a professional farmer, knowing the environmental conditions of our soil is invaluable. Obviously, we can't measure the number of worms or pieces of organic humus, but...

Plant monitoring and watering system with evive
Instructions from Plant monitoring and watering system with evive
Printing the Readings on computer via Telnet client Now you need to print the readings of soil moisture on the telnet. you can put the ESP-12E (ESP8266) module in the given slot for it in evive. For more information about how it works you can see our...

1
2
3
4
5
>
>|