16 Results for "toy"

Up Down Mechanism
Instructions from Cute Drawing Robot - Servo and Android
1) Up down mechanism is quite easy using a old toy car wheel. 2) Just Hot glue the old toy car wheel to the servo arm away from the center. This acts to lift the arrangement smoothly. 3) Fix the arrangement to the other side of the slide.

Building the MIDI I/O circuit
Instructions from Vintage Toy Synthesiser
For a guide on how to do this, please see this log. Feel free to ignore the last part about connecting the circuit to the BeagleBone Black - this will be covered in a later instruction.

Wiring.
Instructions from What does the Fox say? See n' say
Solder the switch contacts to I/O 8 and gnd. Solder wire to the speaker and attach the other end to the amplified output of the shield. Also solder the jumper spots on the shield to increase the amplifier gain to maximum. This will...

Extract Bubble Module
Instructions from Bubblepunk: Wearable Bubble Machine Hacking
Once the toy is open, you can pull all the guts out from the plastic casing. So all you should have left is just the bubble module and some wires and tubes dangling out of it!

Disassemble
Instructions from Bubblepunk: Wearable Bubble Machine Hacking
With many of the bubble blasters, disassembly is really easy! You just unscrew all the screws you see and the toy comes apart in two! The Dinosaur bubbler even comes with a tiny screwdriver to open the battery compartment, but all the screws can be taken...

Breadboard Testing
Instructions from A 555 Timer based Turntable and PCB Shaker Circuit
I have built the circuit on breadboard and tested it. It works perfectly fine. You may observe the video files attached here. I have also used my DSO to test the various PWM and control signals. Do note that we have taken ideal conditions, so we considered...

Wonder if you can make it more simple
Instructions from Energy Independence While Travelling
The best part is the part which isnt there (Or something like that is being attributed to Elon Musk) well ok let's get rid of all those lines... The following vid only has a 1 TRPT line experiment. Can you make a more simple transmission than this one?...

Mesh pads
Instructions from DIY mesh conversion of a simple drum set
The pads are based on toy drums which already have most of the needed bits (like rims and screws) and what missing, I 3D printed.List of main steps: Preparing shellsTrigger and "electronics" (see another instruction)Rim "mufflers"3D printed partsFinal...

Connect Bubble Tank
Instructions from Bubblepunk: Wearable Bubble Machine Hacking
Connect the tube with a 1/8in inner diameter to the inlet tube coming from the bubbler. This is where the bubble juice will go INTO your bubble machine. The soft silicone tube from the bubblers will slide nicely into your 1/8in ID tube! The other tube...

Finishing the body...
Instructions from Droid Trooper
After filling all gaps with epoxic clay and sanding all the robot's body, it's time to finish some details The back piece of the body has some nice holes and deep lines. These lines was covered with black tape after painting the part. You can also...

HOW TO MAKE LOW CONSUMPTION ELECTRIC MOTOR AND TRANSFORM IT IN A DC GENERATOR
Instructions from LOW CONSUMPTION ELECTRIC MOTOR & DC GENERATOR
TEST 1 : TEST 2DC GENERATOR : Materials : 1. VIMUN SC-3012-2A, 29.44mm×11.6mm×1.1mm, 4 cells + voltage rectifier (inside a solar powered flapping toy) 2. neodymium sphere 19 mm diameter (Material NdFeB Shape Sphere Diameter...

Brain controlled Robot
Instructions from Brain controlled Robot
Hacking Necomimi EarsWe followed the instructions documented here to transform Necomimi toy into a bluetooth EEG sensor.Remove the sticker and the back of the device. You will find two small circuits, the one on the top controls the ears and the one...

Experiments & Expansions
Instructions from Mug-O-Matic: A Modular Tiny CNC
It might surprise you but the Mug-O-Matic in drawing mode has a rectilinear coordinate system. Even though its X axis twists, the work piece is also round so it cancels out and the math is still easy. :) You'll see in my examples that I like...

Make the Damping Unit
Instructions from Seismometer
The magnetic damper consists of a copper blade that moves through a strong magnetic field produced by 4 very powerful neodymium magnets. The copper blade and brass bolt are non-magnetic, but the housing IS MAGNETIC so the magnets can stick to it as are...

Badge Basics
Instructions from 2022 Hackaday Supercon 6 Badge Guide
Imagine it's the summer of 1975. A warm breeze blows through the window as you carefully slide the cover over the Altair 8800 you just finished building. You look down upon the rows of LEDs and switches, and realize with a sense of pride that you're...

1
2
>
>|