Results for %EC%A6%9D%EA%B6%8CDB%EC%97%85%EC%B2%B4 %ED%85%94%EA%B7%B8 dbmong %EC%A6%9D%EA%B6%8CDB%EC%97%85%EC%B2%B4 %E2%91%A9 %EC%A6%9D%EA%B6%8CDB%ED%8C%90%EB%A7%A4 %E3%8B%88 %EC%A6%9D%EA%B6%8CDB%ED%8C%90%EB%A7%A4 %EA%B0%9C%EC%9D%B8%EC%A0%95%EB%B3%B4%EB%94%94%EB%B9%84%ED%8C%9D%EB%8B%88%EB%8B%A4

YoctoBob - a BOB for an ultra tiny Cortex M0 proc.
Details from YoctoBob - a BOB for an ultra tiny Cortex M0 proc.
Main features of the LPC1102ARM Cortex-M0 based processor32-bit MCUCPU frequency up to 50 MHz32 kB on-chip flash memory8 kB SRAM11 General purpose input output pins10 bit ADC1 UART1 SPI controllerInternal 12 MHz RC oscillatorConsumption: approx 2 mA...

MashBerry - Beer brewing with Raspberry PI
Details from MashBerry - Beer brewing with Raspberry PI
Hardware The heart of the MashBerry is a Raspberry PI. An interface-PCB is used for connecting sensors like a PT1000, DS1820 or IR. The outputs like beeper and SSR are also connected to the interface-PCB. The PCB mainly contains a I2C-Level Shifter for...

Otter-Iron - TS100 USB-PD hardware mod
Details from Otter-Iron - TS100 USB-PD hardware mod
I Ordering and assmebly instructions The BOM can be found at KiCAD/production/kitspace_bom.csv. Most parts are generic parts, which can be ordered and assembled regulary. However the display and tip-holders need special attention. The PCB has to be ordered...

Z80 homebrew
Details from Z80 homebrew
Phase 1: Prove the Z80 works. Simple wiring with data pins pulled low (nop) and address pins counting on leds. Very excited to see the clock and read wave forms on DSO. Clock is a simple astable 555 circuit. Heavily leaned on Robin Mitchell's project...

Shift Register for Supercon Badge
Details from Shift Register for Supercon Badge
All documentation for the expansion board is available on the Supercon Badge project page. Of course you can do a ton more than this hardware, but blinkies are always the first step! A Demo: The Hardware: The hardware couldn't be simpler. I added a 595...

Digispark GSM relay controller
Details from Digispark GSM relay controller
This project uses the following sites and code as its base, either inspiration, snippets, or educational, during its evolution from super basic building blocks to the final code.http://yesthomas.com/Other/201703-Arduino-A6-GSM.htmlhttps://alselectro.wordpress.com/2016/09/14/gsm-a6-with-arduino-making-a-call-sending-sms/http://makerangst.com/a6-gsm-gprs-module-send-an-sms/2https://www.jagelectronicsshop.com/single-post/2016/11/29/How-to-make-Calls-and-Send-SMS-using-A6-GSMGPRS-Module-and-Terminal-Softwarehttps://www.instructables.com/id/Mobile-Intercom-With-A6-Module-and-Arduino/...

NAS - DIY HDD Bay
Details from NAS - DIY HDD Bay
While reconfiguring my NAS setup made of a ReadyNAS 104 and a ICY BOX IB-RD3640SU3, I tried to connect the external bay to my laptop to access the drives. Only a single drive was accessible when configured as JBOD. With the RAID enable, the bay register...

Controling LCD Shield using EASE & Arduino
Details from Controling LCD Shield using EASE & Arduino
You can read more about this and other Esmacat tutorials on the official Esmacat website. You can also learn more about us on our main website. Detailed documentation of the codes and steps can be found here. EtherCAT Arduino Shield by Esmacat (EASE):...

EASE w/ LCD& Motor Shield Using RaspberryPi Master
Details from EASE w/ LCD& Motor Shield Using RaspberryPi Master
You can read more about this and other Esmacat tutorials on the official Esmacat website. You can also learn more about us on our main website. Detailed documentation of the codes and steps for this tutorial can be found here. Check out our EASE Crowd...

The Human Connection : 1st Impression
Details from The Human Connection : 1st Impression
The Human Connection - 1st ImpressionWhat do the oceans under the ice of Europa sound like? The Europa mission is the "big" vision. What is under the ice? What kinds of sounds are down there? Who is making those sounds and can we communication...

Reverse Engineering the Maverick ET-732
Details from Reverse Engineering the Maverick ET-732
My first step was to figure out the transmitter's frequency. Using a spectrum analyzer, I saw that it sent a signal at 433.92 MHz once every 12 seconds, using what appeared to be on-off keying. I also searched FCC filings using the Maverick's FCC ID...

Compact-size-PCB-for-Arduino-projects
Details from Compact-size-PCB-for-Arduino-projects
Compact-size-PCB-for-Arduino-projects This is multipurpose PCB specially design for arduino projects so that we can connect multiple components at once with arduino Those who ever worked with arduino they know the pain of connecting multiple components...

Project Precision
Details from Project Precision
Way back in the late 80s, I remember seeing a TV show (I think it was Amazing Stories) which featured an interesting clock. It was round, black, about the same size as a normal wall clock, and all done up in LEDs. The LEDs appeared to be what I now recognize...

Word Clock
Details from Word Clock
All files posted at http://www.instructables.com/id/3D-Printed-Word-Clock/THE LIGHT WELLThe heart of the project is the light well. It has two functions, first, create light for only the intended word (light must not bleed into adjacent words). Second,...

8048 Maze Generator
Details from 8048 Maze Generator
The main purpose of this project was to create a submission for the 1kB Challenge. It turns out that 1kB is way more than I needed for this project, so I made it my goal to make this program as small as I possibly could.HardwareAt the heart of the project...