Close

1545 Results for "《〈 문의 OIO↗5793↗7458 》〉 강남셔츠룸ㅬ レresidence㎱강남셔츠룸신사셔츠룸⑧appetite 강남셔츠룸강남란제리 강남셔츠룸╃강남란제리″names㏊"

  • Lexitron RSS Reader

  • Tickernut circuit design and hardware:Enclosure:The motherboard is shaped to fit tightly inside a standard ABS jiffy box which set its limited size. The box has cutouts to expose all motherboard connectors on the left side and a small speaker and antenna...
  • Lexitron RSS Reader

  • Tickernut firmware:Ethernut is an Open Source Hardware and Software Project for building tiny Embedded Ethernet Devices. It consists of a set of hardware designs all running an open source operating system called Nut/OS and a TCP/IP protocol suite named...
  • Lexitron RSS Reader

  • Tickernut construction log:Construction was completed in stages over the period of many months with a design that evolved to suit the available parts.  The progression of construction was arranged so that each stage could be completed and tested...
  • 1Charger

  • Can we build it ?Insert parts in project box and plan for cables and future add-ons ( 5V step-up, switch, GPS, Thermocouple wires ...)
  • 1Charger

  • There can be only oneComplete the 1Charger by soldering the two circuits together ( from step 7,8 )Solder current sense to ATtiny861* new -Vout to PA5 ( pin13)* old  -Vout to PA6 ( pin12)Solder 3.3V buck-boost supply to new Vout* Vcc+ to new +Vout...
  • 1Charger

  • Time to think inside the box...1. Flash ATtiny without CALIBRATION defined ( see step 4 )2. Verify everything works as expected3. Assemble project box and solder connectors.\(^_^)/ DONE !
  • 8-bit Jukebox

  •      Assemble the case: Add a little glue to the edges of each plate (A-1 through A-5) and press fit them together. The arrows and letters on plates A-1 through A-4 should match up as shown in Image 1. You might want to use some...
  • Animatronic Hand

  • Upload the “Rock Paper Scissors” sketch onto your Arduino. The sketch file can downloaded from this page in the "other files" section.2.  Create the circuit.3.  Build the robotic hand. Laser cut the attached file “robotic...
  • DIY evaporative cooler.

  • Basically I set this up in about an hour.   I put a foot deep hole in the flower bed and gave the antenna mast a moderate soil base to keep it from moving.  I also used a piece of yellow twine and and two small penny nails to keep it from...
  • JudgeTron 9001

  • Because judging for the Hackaday Prize isn't something the biological units I intend to use do naturally, I had to build in some positive feedback. Like most evolved biological things, the neural networks here are pretty optimized to sustaining themselves...
  • JudgeTron 9001

  • So I now had input, output and a feedback mechanism. All I needed now is some software and a case.The case was pretty easy: I took a cheap box from my local shop and cut off the upper half. A bit of acrylic glass with a hole in it for the touchscreen...
  • Clone of stEve

  • - On D push four M3 nylon screws 25mm long through from back (side with graphic), add spacers (acrylic donuts) on three and nylon nut on top right (when looking from front) then place Arduino on top.- To the three screws apply a stack of five spacers...
  • Bored No More

  • Dream It!Inspiration Google search on science fair boardsI used Google image search to look at what other projects looked like.  There were some real good looking projects but little innovation in the boards themselves.It is time to break away from...