3515 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Clock in a Box
Instructions from Clock in a Box
The inner dimensions of the box I used: 64mm x 50mm x 44mm with roughly 8mm leeway when adding the top. I probably could have used a smaller box, but it's especially difficult to cram everything in there when including batteries and a holder. So, your...

PiP: Raspberry Pi Portable Slate Computer
Instructions from PiP: Raspberry Pi Portable Slate Computer
Finally I could fit everything together inside the case. But not before finishing the topcoat polyurethane coating. Raspberry Red on the front, matte slate gray on the back.I had to loop some wires inside the case and glue down the ports to the inner...

Floating, Bamboo Makerspace
Instructions from Floating, Bamboo Makerspace
Flooring and Post HolesLay some flat boards across the top of your floating frame. These can be from bamboo that you flatten out in thin strips, or we salvaged some marine plywood from a previous boat.It's important to leave 4 holes in your flooring...

Aeroponic All-year Greenhouse on a Budged
Instructions from Aeroponic All-year Greenhouse on a Budged
ok enouth talk, lets build this thing:First you take one of your pots, put it in the middle of the lid and make a circle around it. Then we are gonna drill some holes....Because i use these Buckerts for everything (including my trash bin), the lid was...

Raspberry Pi Action Cam
Instructions from Raspberry Pi Action Cam
I started by trying to package the peripherals as tightly as possible on the Pi. The largest obstacle was the USB WiFi adapter, which stuck out quite a bit more than everything else. I removed the USB jack with some side cutters and my iron and attached...

Cellular conversion of vintage rotary phone
Instructions from Cellular conversion of vintage rotary phone
Charge your battery. Put a SIM card (with PIN code disabled) into the GSM module. Set the power switch to "on" position. If there are lit LEDs and stuff looks ok, try calling the number of the SIM card from another phone. The bell should ring. If you...

Conclusion
Instructions from Web Form Activity Logger
While Paul built this as an activity tracker he did offer other ideas of how this could be used with some minor changes: Best Coffee/Beer/Restaurant in Town TrackerWhere Are My Friends or Kids Right Now & What Are they Doing? TrackerInteractive Golf...

The Electronic Components
Instructions from DIY Pocket Projector Design
For this project we’re going to need nine different types of components, along with a heat sink of some sort. Three different types of resistors are needed. I went with 1W ratings for each resistor. One 2512 130Ω surface mount resistor, one 2512...

Final:
Instructions from RGB HexMatrix | IOT Clock 2.0
Cut the legs of the NodeMCU board and put everything in the enclosure.Put the screen and make some holes with drill and screw the sides.

Power Up!
Instructions from Fear the Scary Cat!
It's now time to energize the scary cat and amaze all of your family and friends! Insert the cat's base plate into the main housing. You'll notice that there are retaining clips along the outside edge of the bottom housing to help keep everything together....

Fit Everything at Its Place
Instructions from Internal Battery Mod for Korg NTS-1 Synth
Place the wires of the battery board between the USB port and the small coil, as seen on the picture above. After that, place the power switch on the left hole, and fit the USB plug of the battery board on the other one. You have to force a bit to place...

Glue Everything in Place
Instructions from Internal Battery Mod for Korg NTS-1 Synth
Screw back all side panels. Then, put the battery against the side and its USB board, so it doesn't move. It's time to heat up your glue gun! Put some glue on the power switch pin, then behind the battery and on its side to prevent it from moving. Make...

Setting up a PBX server
Instructions from HOW I HACKED MY INTERCOM SO I CAN BE MORE LAZY
To configure a VOIP server on my raspberry I almost cried. Tried any docker PBX image, some worked but the networking was completely broke, some were so outdated and at some point I even installed FusionPBX that broke my entire raspberry configuration...

Heated Bed for M3D 3d Printer
Instructions from Heated Bed for M3D 3d Printer
Mounting resistors and panelIf you have the second 85 mm square sheet cut as well place it in the middle of the bigger cut sheet. You can temporarily use tape to stick them together and make sure they fit into the printer together. If they don't check...

Mechanical Assembly:
Instructions from Delta Robot Automatic Pick & Place Machine
Start by 3d printing the rod connection and the end effector STL FILES on thingiverse. After that use wood or steel for the base I recommend its CNC cut for the precision as well as you should for the arms I made them from alucobond the material used...

|<
<
3
4
5
6
7
>
>|