560 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》강남레깅스룸ⓨ강남레깅스룸singing강남레깅스강남레깅스룸강남레깅스룸remainder 강남레깅스㉮┢선릉레깅스agitation"

Arduino DMX 512 Tester and Controller
Instructions from Arduino DMX 512 Tester and Controller
Working...

Redtree Hydra: A modular platform for robotics
Instructions from Redtree Hydra: A modular platform for robotics
Attaching a SensorIn order to attach a sensor, motor, camera or other component to the Redtree Hydra, the FPGA inside must be programmed. We know that this is normally a tricky task, so we created a tool to simplify it. The Redtree Hydra has four I/O...

Square Foot Gardening
Instructions from Square Foot Gardening
Building and setting up the garden box1. Buy the lumber and supplies. I got everything at Lowes in one trip for a total cost of about $150. Soil is expensive as it turns out. - pro tip on the lumber, the 16 foot long is the cheapest, and you get a 45"x...

Unix on your breadboard
Instructions from Unix on your breadboard
Insert Fubarino board into breadboard, centered. Use 5-wire cable to connect the LCD module to appropriate signals of Fubarino board, according to the following table and picture:LCD moduleFubarinoCS16WR17Data18GndGNDVcc3.3V

64x32 RGB LED Matrix Bare Metal Tetris
Instructions from 64x32 RGB LED Matrix Bare Metal Tetris
Raspberry PI GPIO WiringSNES/NES controllerConnect SNES/NES 5V to RPI 3.3V (NOT 5V!)Connect SNES/NES GND to RPI GNDConnect SNES/NES Clock to GPIO 2Connect SNES/NES Latch to GPIO 3Connect SNES/NES Data to GPIO 4RGB LED Matrix:Connect ADDRESS A to GPIO...

WeatherPi - Solar Powered Raspberry Pi Station
Instructions from WeatherPi - Solar Powered Raspberry Pi Station
Sizing Your Solar Power SystemOne of the first things that comes up in a solar powered design is how to design the power system. The three main questions to be asked and answered are:How much power do I need? How many solar panels do I need? What size...

WeatherPi - Solar Powered Raspberry Pi Station
Instructions from WeatherPi - Solar Powered Raspberry Pi Station
Full Wiring ListFollowing is the complete wiring list for WeatherPi. As you wire it, check off each wire for accuracy.Key: Raspberry Pi A+: PiA+I2C Bus Mux: I2CMDual WatchDog Timer Board: WDTWeatherPiArduino: WPAUSB Power Control: USBPCSunAirPlus: SAPRaspberry...

Automatic Home surveillance system using arduino
Instructions from Automatic Home surveillance system using arduino
Step 3: Program the surveillance system code to the arduino:Once you read the remote button hex codes then now this is time to put main program code into arduino.The bellow program is arduino program for this project automatic surveillance system. upload...

CAN BUS Gaming Simulator
Instructions from CAN BUS Gaming Simulator
Arduino Source Code://############################################################################################################## //Volkswagen CAN BUS Gaming //Test Sketch v3.0 //(C) by Leon Bataille 2015-2016 //Hackaday Project Page: https://hackaday.io/project/6288-volkswagen-can-bus-gaming...

3D Compass
Instructions from 3D Compass
Top Plate Assembly- Attach the magnetometer with 4-40 nylon screws. Shear the excess length flushwith the bottom of the plate using a hobby knife. Be careful to not breakthe superstructure on the printed part.- Place the capacitor into the cut-out and...

3D Compass
Instructions from 3D Compass
Wiring- Trim and solder the data-in wire on the vertical ring to the data-out padon the 24-element ring.- Connect the data-in pad on the 24-element horizontal ring to pin 13 on theArduino. The resistor goes in-line here as well. You can use 0.1" header...

Nano Bike Alarm
Instructions from Nano Bike Alarm
Software ConfigurationOnce you have the hardware complete, extract the package and open the 'newKey' sketch.In the Arduino IDE, edit this sketch and change the hex values for the newA and newB keys and for the tokenBlockData array. The keys are 6 bytes...

operation: Learn The MIPS (PIC32MX1xx/2xx/370)
Instructions from operation: Learn The MIPS (PIC32MX1xx/2xx/370)
Wire up your PIC32's MINIMUM requirements as-shown:(a summary of the related Project Log)(NOTE: If this page wraps-weirdly, try *shrinking* your window-width, counterintuitively)( '#' = MUST BE CONNECTED ) ( '*' = 5V-tolerant ) 3V3 ^ | \ / 10K PIC32...

operation: Learn The MIPS (PIC32MX1xx/2xx/370)
Instructions from operation: Learn The MIPS (PIC32MX1xx/2xx/370)
Wire the PIC32's JTAG pins to the FT2232H breakout-board/JTAGger:Pin Mapping: PIC32MX2xxFxxxB JTAG signal FT2232H (JTAGger) 14 TMS AD3 16 TDI AD1 17 TCK AD0 18 TDO AD2 (GND) (GND) (GND) (3V3) (3V3) (3V3) NOTE: I'm assuming you're taking 3V3 FROM the...

IBDAP - Affordable CMSIS-DAP JTAG/SWD Debug Probe
Instructions from IBDAP - Affordable CMSIS-DAP JTAG/SWD Debug Probe
OpenOCD Tutorialinstall depssudo apt-get install build-essentialsudo apt-get install autotools-dev autoconf automake libtoolsudo apt-get install texinfo libudev-dev libusb-1.0-0-dev libfox-1.6-devDownload FTDI driverhttp://www.intra2net.com/en/developer/libftdi/download.php...

|<
<
2
3
4
5
6
>
>|