1008 Results for "강남권룸싸롱【θ1θ↔4⑥48↔0⑨30】xavi서울룸싸롱±선릉추천업소￡역삼풀싸롱ksubi강남룸접대paul서초풀싸롱σ강남추천업소θ선릉풀싸롱δ"

SOLAR POWERED ARDUINO WEATHER STATION
Instructions from SOLAR POWERED ARDUINO WEATHER STATION
1. Making The Transmitter : The transmitter module contain the various sensor for monitoring the weather.The DHT11 sensor is used for measuring temperature and humidity of the environment.It is good for 20-80% humidity readings with 5% accuracy and for...

Make and Feel Virtual Drawings
Instructions from Make and Feel Virtual Drawings
Make Processing control Arduino THE FINAL PROGRAM:So,you have started drawing on Processing. Now, you'll 'feel' the drawing!Imagine you are blind (remember, this device was invented for blind people to draw on computers):How would you feel a raised line...

Code for single Esp32 Board
Instructions from Bluetooth Tracker
This is the code for everything on a single Esp32 Board. Since I didn't have the correct board, I needed to use two of them, and they communicate through the serial port.The Bluetooth packets address and raw data get printed to the Arduino Serial...

Wii Stream: Turn your Wii into a Sonos
Instructions from Wii Stream: Turn your Wii into a Sonos
Introduction This guide details the steps for installing WiiStream on your Nintendo Wii. Follow each step closely for a successful setup. Prerequisites A Nintendo Wii matching one of the model numbers hereAn SD cardA PC with internet access (here...

Addressable MUX code
Instructions from Synth Design System - Addressable MUX Circuit
As mentioned, one of the reasons for developing this system is that I do not want to rewrite code every time I start a new synth project.The idea with this project is that when initialised the microcontroller will poll each possible card address and...

Granulate Reservoir Assembly
Instructions from Bloft Mk2 - 3D printer for plastic waste
We will now add a small reservoir for plastic pellets on top of the hopper section. The reservoir has a material level sensor to trigger the dispensing system once the level has dropped below the threshold. Prepare: 3D printed Separator Adapter Plate3D...

Code
Instructions from Safe City: A Device to Keep You Safe
#include "SoftwareSerial.h" String ssid ="yourSSID"; String password="yourPassword"; SoftwareSerial esp(6, 7);// RX, TX String data; String server = "yourServer"; // www.example.com String uri = "yourURI";// our example is /esppost.php int DHpin = 8;//sensor...

Bill Of Material
Instructions from Gesture/Pattern Recognition Without Camera : TOF !
Here is an idea of the minimum and maximum manufacturing cost of the project (for one unit) ComponentQuantityTotal PriceTeensy 3.2119$LCD 128x12816$TOF VL53L1X19$USB Micro14$BreadBoard / Wire / Header / 3D Print / LED110$Minimum Config total48$Replace...

Trinket LED Thermometer
Instructions from Trinket LED Thermometer
Here's a functional program to initialize the hardware, read temps, and display temps as colors. Enhancements such as multiple sensors/LEDs per Trinket are possible but left as an exercise for the reader./* trinket_thermo ---------------------------------------------------------------------------------...

Second meeting
Instructions from Analog meter Arduino Clock
Second meeting 1. Hand out the Arduino, RTC module, wires, alligator clips, USB power block and USB cable 2. I ask them how we are going to have the Arduino control the meters ? I explain what PWM signal is and how we can use...

DIY CO2 Laser
Instructions from DIY CO2 Laser
Gas mixture and source:This is the gas litering piston assembly under construction. It is constructed of a 4" x 2/58" glass cylinder. The teflon piston seals completely and can evacuate 100% of the gas. Volume is the V = Pi x r x (h - 1/4). V= 3.1415926...

Electric Typewriter to Teleprinter
Instructions from Electric Typewriter to Teleprinter
If we want this to be emulated by a microcontroller, we need to feed it the "scan" as an input and have it output to "in". Also we need to know which combination "presses" what key. This can be done going through all permutations of possible connections...

Instructions for use
Instructions from GPS Clock
When the clock starts, it will briefly light up all LED segments as a test, then display "no GPS", which means the GPS signal hasn't been established (or has been lost). At any time, you can click the "set" button to enter the menu system. Once there,...

Step 12: Setting up the neural network model on Beetle ESP32-C3
Instructions from Multi-Model AI-Based Mechanical Anomaly Detector
After building, training, and deploying my neural network model as an Arduino library on Edge Impulse, I needed to upload the generated Arduino library on Beetle ESP32-C3 to run the model directly so as to detect sound-based mechanical anomalies with...

PCB Fabrication
Instructions from Adjustable Timer Switch
Estimated Time: 30 mins Order PCB:PCBWayEagle PCB Board Layout: GitHubPrintable PDF: GitHub I fabricated the board using the Iron Method. I drilled four mounting holes in each corner with a diameter of 3mm. The PCB size is 10cm X 5cm .

|<
<
4
5
6
7
8
>
>|