Close

1008 Results for "강남권룸싸롱【θ1θ↔4⑥48↔0⑨30】xavi서울룸싸롱±선릉추천업소￡역삼풀싸롱ksubi강남룸접대paul서초풀싸롱σ강남추천업소θ선릉풀싸롱δ"

  • Raspberry Pi Console
  • Instructions     from Raspberry Pi Console
  • Make the LEDS light up on bootI connected a transistor to GPIO4 which turns on the LEDS when it's base is LOW. When the RPi is powered but halted, the LEDS will be off. When the RPi is powered and booting, the LEDS will be on.First, edit rc.local file...

  • 16bit RISC Processor
  • Instructions     from 16bit RISC Processor
  • First the instructions- Each instruction is of 16 bits that means [15:0]. Further dividing itwe select opcode- [15:12] then rest [11:0] bits depend on the instructions.For R type we have ADD [--R1--] [--R2--] [--R3--] Each Register here is of 4 bits.So...

  • Run a Program
  • Instructions     from Measure Water Level using JSN SR-04T Sensor
  • #includeLiquidCrystal lcd(12, 11, 4, 5, 6, 7); // sets the interfacing pins#define ECHOPIN 3#define TRIGPIN 2void setup() { Serial.begin(9600); lcd.begin(16, 2); // initializes the 16x2 LCD pinMode(ECHOPIN,INPUT_PULLUP); pinMode(TRIGPIN, OUTPUT); digitalWrite(ECHOPIN,...

  • Run a Program
  • Instructions     from Interfacing PCF8591 ADC/DAC Module with Arduino
  • #include #include#define PCF8591 (0x90 >> 1)#define AIN0 0x00const int rs = 12, en = 11, d4 = 5, d5 = 4, d6 = 3, d7 = 2;LiquidCrystal lcd(rs, en, d4, d5, d6, d7);int Value = 0;void setup(){ Wire.begin(); lcd.begin(16,2);}void loop(){ Wire.beginTransmission(PCF8591);...

  • Run a Program
  • Instructions     from Arduino Wattmeter - Voltage and Power Consumption
  • #include int Read_Voltage = A1;int Read_Current = A0;const int rs = 2, en = 4, d4 = 9, d5 = 10, d6 = 11, d7 = 12; LiquidCrystal lcd(rs, en, d4, d5, d6, d7);float Voltage = 0.0;float Current = 0.0;float Power = 0.0;void setup() { lcd.begin(16, 2); Serial.begin(9600);...

  • Boolean Logic HDL
  • Instructions     from Computer build from first principals
  • /** * 16-bit bitwise And: * for i = 0..15: out[i] = (a[i] and b[i]) */ CHIP And16 { IN a[16], b[16]; OUT out[16]; PARTS: And (a=a[0], b=b[0], out=out[0]); And (a=a[1], b=b[1], out=out[1]); And (a=a[2], b=b[2], out=out[2]); And (a=a[3], b=b[3], out=out[3]);...

  • Arduino Teletype
  • Instructions     from Arduino Teletype
  • #include//Baudot lookup tableunsigned char lookup[] = { ' ', 'E', ' ', 'A', ' ', 'S', 'I', 'U', '\n', 'D', 'R', 'J', 'N', 'F', 'C', 'K', 'T', 'Z', 'L', 'W', 'H', 'Y', 'P', 'Q', 'O', 'B', 'G', 0, 'M', 'X', 'V', 0, ' ', '3', '\n', '-', ' ', '`', '8', '7',...

  • PROGRAMMING
  • Instructions     from ESP-01 CONTROL RGB LED CUBE 4x4x4
  • In my program, ESP-01S ESP8266 is used as a stand-alone device to control a RGB led cube 4x4x4. The project code is available at my GitHub. CONNECTIONThe ESP-01S ESP8266, 74HC595 & TPIC6B595N are connected together as follows: LED CUBE CONTROLFor layer...

  • Use CoilScanL with an existing coil form
  • Instructions     from Inductance design tools
  • # # Make a 12uH coil using an existing 48mm form # > CoilScanL --LTarget=12 --DForm=48 --lMin=20 --lMax=250 --lInc=10 --d=1.44 --f=13.562 # CoilScan 2023-03-11 13:21 # # LTarget = 12, d = 1.44, p = 6, f = 13.562 # # DForm = 48, lMin = 20, lMax = 250,...

  • Summary
  • Instructions     from Grasp Bionic Hand
  • Assembly steps Printing and removing support material Fingers assembly Thumb assembly Inserting the motors on the palm Inserting the motor on the thumb Fingers and palm assembly Casting silicone in the molds Gluing the silicone “skin” in...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday