6194 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Building the AUV - Internal
Instructions from Project Albatross
The internals of the AUV performed the heavy work of actually taking water quality measurements and controlling the submersible's buoyancy. Evidently, it also required a sophisticated mechanical design to fit the necessary components into the confined...

The world's first paper quadcopter
Instructions from The world's first paper quadcopter
Repeat step 1 and then cut to 11 inchs. make sure everything is even and tape some more on the ends of tube.These are the arms.

IoT Connected Picture/Desk Frame
Instructions from IoT Connected Picture/Desk Frame
4. The Front coverAfter printing the Front cover on transparent foil everything is read to be assembled together:

9
Instructions from Harmonic Gear Driven Star Tracker
insert motor (with motor mount and oval drive installed) mount onto stage 1 and bolt everything together with 4x M3x60 bolts and 4x M3 nuts

Glue the generator parts together
Instructions from Propel-E 450 | A very powerful windturbine
Add glue to each part and press everything together firmly for half a minute. That should be enough to hold everything in place. Warning! Only glue the top 4 parts together, and the bottom 4 parts. Don't add top and bottom together yet because the stator...

Wrapping up
Instructions from 3-Axis Skull Mod for 12ft Skeleton
Once again make sure everything is tight and everything is free to move without binding. Add servo extension cables for the 4 servo cables as they are very short when exiting the skull.Test, test, test!!!Enjoy!

Turn a cigarette lighter into an IR Nikon remote
Instructions from Turn a cigarette lighter into an IR Nikon remote
4.Wire everything as in the schematic diagram. The LED does not need a series resistor. Internal resistance of the cell batteries are doing a pretty good job in limiting the LED current.

1Charger
Instructions from 1Charger
Time to think inside the box...1. Flash ATtiny without CALIBRATION defined ( see step 4 )2. Verify everything works as expected3. Assemble project box and solder connectors.\(^_^)/ DONE !

Step 4
Instructions from Grounded Dell 45W PD
Put everything back. The plastic covers might be loose so you can apply a little bit of glue. hot glue is preferred as it don't generate fumes. otherwise one or two drops of epoxy will do. Or just use straps, tapes or whatever.

Connections
Instructions from Rainbow Lamps
Connect all the electronic components as shown in the circuit diagram.Make sure everything is connected as per diagram before you power it on.

Assemble everything
Instructions from Lor's Electronic Heart
1. Cover the cell with Thread to make it bit not ugly.2. Place all the components on perf board before soldering to make sure everything fits under the board size.3. Solder NE555 ic with other passive components including the tactile switch, then solder...

Re-assemble and Test
Instructions from Internal Battery Mod for Korg NTS-1 Synth
Now you can put the NTS-1 board back in place to test if everything works. The red wire than goes inside should be placed in the empty space on the top-left side of the board, as pictured here. Before going any further, it's time to test if everything...

Hacking AngelCare® Breathing Sensor with Arduino
Instructions from Hacking AngelCare® Breathing Sensor with Arduino
The first thing to do is to get rid of the 1/8 jack that came with the sensorThen I put some soldering in the end of the cable so it can be easy to stick it in the protoboardConnect everything as the the Fritzing Diagram suggestDownload the Arduino Sketch...

1. Hand soldering the pin
Instructions from K.I.T.T. - KNIGHT RIDER badge/brooch
Add solder to one pad, use pliers to hold the hin in place and solder everything together. After that use heat the second pad and the clip simultaneously and add solder to fix up the second pad. You need to start with the clip because it takes a lot...

Materials You Will Need:
Instructions from Arduino NodeMCU automated Room
1-NodeMCU ESP8266 board 1-PIR sensor 1-LM35 temperature sensor 6- 3904 NPN transistors 4-1n4001 diodes. 8-1k ohm resistors 4-5v relays 2-12v relays (can be replaced by 5v ones). 8-Terminal blocks Some wiring to connect everything and that's it.

1
2
3
4
5
>
>|