1493 Results for "%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%EA%B0%95%EC%B6%94%E2%9C%9Awww%2Coptime4.com%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%20%EC%9D%B8%EC%B2%9C%EB%A7%88%EC%82%AC%EC%A7%80%20%E2%9C%9A%20%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%E1%98%9B%20%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%EC%82%AC%EC%A7%84%E1%98%9B%20%EC%9D%B8%EC%B2%9C%ED%9C%B4%EA%B2%8C%ED%85%94%20%EC%9D%B8%EC%B2%9C%ED%82%A4%EC%8A%A4%EB%B0%A9%20%ED%83%80%EC%9E%84"
Plug in your Cat's nervous system. Connect the Photon to your other components. I do this by using 3x20 breakaway right angle headers where several rows have been shorted together to be power and others to be ground. This lets me better organize my components.Pin...
Solder wires from UBBB to LCD. (Note that uBBB pins are ordered as if looking at the bottom, since it also serves as a generic 32-TQFP breakout board if you flip it upside down). Specific connections are described below:-Connect pins 1, 5, and 16 on...
Next, you need to trace your design onto your pumpkin. We used a Dracula-ed version of our icon aka BitGuy. Download the PDF below, or use one of your own designs! Carve your pumpkin and remove all the guts. PRO TIP: spray the inside of your pumpkin...
It's in the GITHUB! The code comes down the these smaller steps: MQTT handling and Button handling. Let's do button handling first. I made a simple button object with the pin number, button press boolean, and button count. struct Button { const uint8_t...
Making the dog walk is quite the challenge, so here's my approach. I created a drawing showing "standing" leg positions in black and progressive changes in red. The approach is to: 1) lift the left front and right rear legs 2) move the left front and...
Calibration1. #define CALIBRATION in software and recompile and flash ATtiny8612. For each range make two measurements in order to calculate the line v=k*ADC + m. With this simple approach I get about 10-20mV and 10-20mA accuracy ( compared...
Here's a functional program to initialize the hardware, read temps, and display temps as colors. Enhancements such as multiple sensors/LEDs per Trinket are possible but left as an exercise for the reader./* trinket_thermo ---------------------------------------------------------------------------------...
To bend the foam...Add some adhesive tape on the backside of the foam and you can safely bend it.I learnt this trick from Ed at Experimental Airlines and used the tool to build his Photon glider.
Setting Up the EnvironmentRedtree Hydra currently requires a Ubuntu or Debian based development environment. For the remaining instructions, open the terminal application in Ubuntu. In Ubuntu It can be found by clicking the Ubuntu search icon on the...
The connections on the Octosonar are clearly labelled. I'll try and run up a wiring diagram later, but for now the following list of connections should get you there. To connect to Arduino Octosonar PinUno Pin DefaultDescription5V5V5V supply for...
Time to start putting together the low-side driver board with the CAT4101s. First step is to install the connector on the 11 x 8.5 cm protoboard. This is the spec'ed component, but if you can't find one that size, you can use another one up to 11.5 cm...
Next thing was the PSU. Since I had a spare NiftyCase laying around, and they have a PSU / MIDI In and Audio Out already in the case, I decided to just canibalize this. The NiftyCase electronics consists of two PCBs, connected with a ribon cable. I laser...
"U" frameMethod a) just use a vicemethod b) bend the shelf rail in three steps:b1) put the shelf rail on the table edge and firmly bend it to mark the locationb2) put the shelf rail on the floor, put a chair on top and sit on it, bend the shelf rail...