63 Results for "%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%EA%B0%95%EC%B6%94%E2%9C%9Awww%2Coptime4.com%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%20%EC%9D%B8%EC%B2%9C%EB%A7%88%EC%82%AC%EC%A7%80%20%E2%9C%9A%20%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%E1%98%9B%20%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%EC%82%AC%EC%A7%84%E1%98%9B%20%EC%9D%B8%EC%B2%9C%ED%9C%B4%EA%B2%8C%ED%85%94%20%EC%9D%B8%EC%B2%9C%ED%82%A4%EC%8A%A4%EB%B0%A9%20%ED%83%80%EC%9E%84"
First, let's assemble the extruder, so we can just drop it onto the printer later! There are two sets of spacers, labeled B1-B7 for the Bottom assembly, and T1-T2 for the top assembly. There is also an extruder motor shaft coupler spacer, labeled...
Cut a piece of the tube to the right length with a hacksaw:The tube is 6 mm dia. hollow aluminum tube, with ~1 mm thick walls. This conveniently leaves 3-4 mm of space in the centre. I bought mine in B&Q: http://www.diy.com/departments/ffa-concept-aluminium-round-tube-l1m/254217_BQ.prdOnce...
Check the following image on how to install the hings on your kitchen skirting board. If the hing is not centered like in the middle picture, your skirting board won't hang in a 90° angle from your cupboard. However, when the hinge is centered and...
howto make a generator1. 3V Dc motor – inside toys which using two batteries 1.5 V AA 2. coil without core inside syncronous motor 230 V – A4 laminators, microwave turntable motor - remove the core inside the motor 3. neodymium magnet sphere 13 mm 4....
Place a regular 1/4" 20 nut on all bolts sticking out of the frame and then add a lock washer above the nut. I spun the nut down as far as it would go with my fingers. Screw on all the Ball head mounts on top of the bolts. They will vary slightly in...
Print axle.stl that will serve as a holder for the bearings. The 20 mm rod that goes in it will do the heavy work. The axle bolts on any flat surface with 4 10mm bolts. After the axle has been fitted, glue the raincap on top of it, using the same process...
For this step you will need: Acrylic sheetsSawPencil I am using some 3mm thick opal acrylic to diffuse the light for this project. I purchased some A4 sheets which we can cut three panels worth of acrylic diffusers from. My fourteen triangles therefore...
The rest of the BOM items are off the shelf devices, therefore you can purchase these from a number of sources like https://www.digikey.com/ or https://www.mouser.com/. The BOM I have attached to this project show Manufacturer, Manufacturer...
I used an empty tomato paste can to hold the lead weight of the mass. (A tomato sauce can is too wide.) shorten the can to be approximately 1.5" tall.drill a 1/4" hole in the center of the bottom of the can.push a 1.5" long 1/4 x 20 bolt into the...
First of all, we will install the servo motor in the number 1 part. Mount it using the two long screws that come out of the servo motor package. Mount the servo motor with 4 10 MM spacers and 4 nuts to the part number 1 where we mount it. These spacers...
The components are attached to a baseplate (95(W) x 128(L) mm), which is fitted to the back of the MDE's with M3 X 25mm bolts and 10mm standoffs. Four bolts are fitted through the holes in the Neopixel support board and the standoffs fitted to attach...
Prepare the chassis.Drill a hole centered in each of the two "short" sides of the case sized for the CG-16 cable gland. Drill a hole sized for the L6-20 receptacle. The hole should be centered horizontally on the panel, but the top edge should be as...