Close

5533 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

  • 3D Print Some Parts
  • Instructions     from Paper Pikon with 1000mm Focal Length
  • I suggest starting by printed some parts.  You'll need most, if not all, of the parts from the original Pikon:  https://www.thingiverse.com/thing:2200862 To build this out of paper I would exclude the Tripod mount & Raspberry Pi mount. ...

  • GCODE Commands
  • Instructions     from DIY Inkjet Printer
  • The printer can be controlled by sending values via i2c. Each set bit represents a printer command like: 0 - everything off 1 - single drop printhead 1 2 - single drop printhead 2 4 - single drop printhead 3 8 - single drop printhead 4 16 - drops at...

  • Wiring everything together
  • Instructions     from PocketWhale
  • This is gona be a long step... Below i'm putting wiring diagram (or something that suppoused to look like on). 1. Powerbank 2. Mi band 3. Solar charging board 4. Solar panels 5. LCD screen 6. USB C for powering raspberry pi 7. Magnetic conector...

  • The final
  • Instructions     from BrailleRAP DIY Braille embosser
  • Adjust everything, tight the needed screws and beltsAdjust the top and bottom carriage, the Braille stylus of the bottom carriageneed to slighty enter in the anvil of the top carriage.Mount the electronic board with driversWire the 12V alimentation Adjust...

  • Clock in a Box
  • Instructions     from Clock in a Box
  • The inner dimensions of the box I used: 64mm x 50mm x 44mm with roughly 8mm leeway when adding the top. I probably could have used a smaller box, but it's especially difficult to cram everything in there when including batteries and a holder. So, your...

  • Raspberry Pi Glowbe Wake Lamp
  • Instructions     from Raspberry Pi Glowbe Wake Lamp
  • We’ll run the code with cron. It should start about half an hour before you get up and probably only on weekdays. Launch the cron configuration by typing the following into a terminal: crontab -e Next, set it up by adding the following line to the end:...

  • Raspberry Pi Action Cam
  • Instructions     from Raspberry Pi Action Cam
  • I now had a pretty good idea what the final x and y dimensions were going to be. I wanted to keep the camera as close to the size of the Pi as possible, which meant the large battery had to fit snugly underneath the bottom of the Pi. I printed out a...

  • PolaPi v2.0
  • Instructions     from PolaPi v2.0
  • install fbcp (so you see the console on the GPIO Display)sudo nano /etc/rc.localdelete everything and add this text#!/bin/sh -e # # rc.local # # This script is executed at the end of each multiuser runlevel. # Make sure that the script will "exit 0"...

  • Norman, Coordinate
  • Instructions     from Norman, Coordinate
  • Amulet wiringNote: The wires typically used for an electronics project will not work in a costume! Typical project wires can only be bent a couple of times before breaking. They are not made to withstand the constant (even gentle) bending and flexing...

  • Test parts and fit
  • Instructions     from Better Cooling for 3D Printer Extruders
  • The heat sink had to be cut to size. Just chopped it up with a hacksaw and Dremel cutting wheel. I used a broken fan to align the holes to be drilled.It took a few tries to get the heat sink to clear everything. There was a metal bracket on the...

  • Bootstrapping
  • Instructions     from External Captions for Video Installations (extsub)
  • If everything is working, press ctrl+c to kill extsub.py, then follow these steps to run extsub at boot.   1. Make startup.sh executable: chmod 755 startup.sh   2. Open /etc/rc.local: sudo nano /etc/rc.local   and add this line so extsub...

  • From CAD to 3D
  • Instructions     from Replacement Faceplate for Pyle PLMR24 Speakers
  • Once the CAD model was created, it was a simple matter of loading the STLs into the Cura slicer and sending the data to the 3d printer. I printed everything at a 0.3mm layer height, since it didn't have to be perfect. Even at that, it looks pretty good....
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday