5533 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Main "module" assembly
Instructions from Open TEG Harvesting Module 2.0
Before getting started please find a spot to assemble the unit where you have a large flat surface and place something down on your surface to prevent a mess (the thermal compound and silicone sealant can get pretty messy.1. Apply thermal compound to...

Open LIDAR
Instructions from Open LIDAR
Assembling the Circuit BoardNote: Before ordering a circuit board make sure to add mounting holes to the file in KiCad. Alternatively, you can drill the holes manually later wherever they will fit. Note: The holes in the provided file were too small...

Feather HUZZAH Setup using the Arduino IDE
Instructions from Connect your Feather HUZZAH ESP8266 to Ubidots
Begin by connecting your Feather HUZZAH ESP8266 to your computers USB port to configure the device. 1. Download the Arduino IDE if you not already have it. 1a. Open the Arduino IDE, select Files -> Preferences and enter the URL below into the Additional...

Switch
Instructions from Electro Knife for Simulated Combat EleKSCo
Safety check: remove the battery. Take all the electronics from the previous step and push them into the handle, but pull the two switch wires out the drilled hole. The high voltage wires need to stick out of the end of the pipe by the switch. If everything...

Electric wiring/soldering (Part 1: everything beside the LED)
Instructions from Retro Slide Projector "Green-Edition"
After some failed tries with pre-built Coaxial Power Connectors from China, I decided to go for Molex-connectors known from computer power supplies. Please be careful: most Y-cables you can buy on Ebay are not made for the high current we are using -...

Install Basic components
Instructions from Retro LED-Beamer with Raspberry Pi/RaspiCast
It is possible to install everything headless, so you can just plug the SD card into your Raspberry Pi and plug in the power. The Raspberry should boot up and after some seconds you should be able to ssh into it with the hostname raspberrypi. Username...

Quick and Nasty Tube Power Supply
Instructions from Quick and Nasty Tube Power Supply
For this step you will want a variac or some way to limit the mains current. You might want to put a lamp in series with the hot wire to the transformer (are you sure you're comfortable working with mains electricity?)Connect everything up as you did...

Pressure Cooker Vacuum Chamber
Instructions from Pressure Cooker Vacuum Chamber
Step 2: Prepare the pressure cookerNow for the fun part. In this step, you'll be drilling a hole in your nice shiny new pressure cooker. I know, it's tough, but it's for a good cause.You're going to need: A metalworking drill pressThe pressure cookerA...

Remote Water Consumption Display
Instructions from Remote Water Consumption Display
Build Instructions.Huh.I'm honestly not sure what to put in this section, but the rules say I need build instructions.I mean, I am posting all of the schematics in the Build Log entries, All of the source code is up there. When I get to the point I have...

Kindle as a home automation controller/sensor
Instructions from Kindle as a home automation controller/sensor
1st build (for computer)The toolchain provided by Samsheff supports C99 so am I. If you have a decent C compiler (clang or gcc), first of all check on your computer everything is ok.kindle-home-automation $ make build cc -Werror -Wall -ggdb -pedantic...

SF02/F laser rangefinder hack
Instructions from SF02/F laser rangefinder hack
USB hack # 1When a product is manufactured, it undergoes a bunch of tests to make sure that everything is working properly. There are also factory settings that need to be entered so there is a way of getting access to these factory functions. For the...

ESP-12F Raspberry Pi GPIO SDIO Wifi
Instructions from ESP-12F Raspberry Pi GPIO SDIO Wifi
Building the DriverInstall prerequisite packages on Raspbian to build the kernel.#make sure everything is up to date sudo apt-get update && sudo apt-get -y upgrade #install tools sudo apt-get -y install bc rpi-update git libncurses5-dev Get the kernel...

Pi-Berry Laptop-- The Classic DIY laptop
Instructions from Pi-Berry Laptop-- The Classic DIY laptop
Making The Base !To begin with.. we will start the build by making the base of the laptop. This is the part where all the components will be screwed (or glued in some case). To make the base1) Mark the locations of the components 2) mark the Drill Points...

Pi-Berry Laptop-- The Classic DIY laptop
Instructions from Pi-Berry Laptop-- The Classic DIY laptop
Assemble the TopAfter we have covered the parts in Italian Leather we need to start putting everything together. To start with we assemble the top part, where the keyboard is fitted.1) Using some 2.5mm MDF pieces, make the keyboard holder. the small...

Phishing WiFi hotspots with captive portals
Instructions from Phishing WiFi hotspots with captive portals
Let's change the hotspot's name. The default one should be something like Omega-XXXX where the X's are usually digits: nano /etc/config/wirelessChange the Omega's SSID to the SSID of the network you want to impersonate.Now it's time to recreate the website...

|<
<
3
4
5
6
7
>
>|