Close

1230 Results for "%E3%80%8A%20%EC%98%88%EC%95%BD%EB%AC%B8%EC%9D%98%20OIO%E2%86%978489%E2%86%978306%E3%80%8B%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80%E2%94%A6%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80world%EC%84%A0%EB%A6%89%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80%EC%82%AC%EC%9D%B4%EC%A6%88%EC%B2%AD%EB%8B%B4%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80promotion%20%EC%84%A0%EB%A6%89%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80%E2%94%AB%20%E2%88%AB%EC%84%A0%EB%A6%89%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80decided"

  • Address Bus
  • Instructions     from L-Star: Software-Defined 6502 Computer
  • This last step is going to get REALLY tedious because the Address Bus has so many lines. But this is the last step and you should be done, so keep it up just a little longer. A0: 6502 Pin 9 to FLiP pin 13 A1: 6502 Pin 10 to FLiP pin 14 A2: 6502...

  • All to do with table saws
  • Instructions     from All to do with table saws
  • The jimmy jig/ used 1/2in ply cover with laminate both sides, hardwood telescoped rails, or 20/80 aluminium extrusions and a clamp that forces the jig rails against the frame that surrounds the table saw/ rock solid, the fence will never deviate from...

  • Lighting Design
  • Instructions     from Long Range RFID Controlled Dry Cleaner
  • We had to do lots of experimenting with different types of glow powders and different types of lighting.LightsFor the best "pop" highlighting the fine details of your leaves, you want a really low wavelength (below 400nm, like 390nm). This reduces the...

  • Bill of Materials (Sans Lens)
  • Instructions     from DIY Pocket Projector Design
  • LCD: $17.56Round Heat Sink: $3.63LED: $0.34130Ω Resistor: $0.362.2kΩ Resistor: $0.41BD 139-16 Transistor: $0.40BC 547 Transistor: $0.20Slide Switches: $0.76200Ω Resistor: $0.76LCD Port: $1.01PCB: Varies wildly, PCB Way is a good one,...

  • Voices of the past, speak up!
  • Instructions     from Voices of the past, speak up!
  • You will need the text to speech board from Mikroelektronika: https://www.mikroe.com/text-to-speech-click Don’t forget to jumper it for 5 V! By default it is set of 3.3 V! You can solder it in directly, but make sure you have enough clearance for the...

  • Crazy Clock
  • Instructions     from Crazy Clock
  • Obtain a clock movement or remove the one from the clock you intend to modify. The recommended clock movement if you wish to start with a fresh one is the Quartex Q-80, available from Klockit. It's also the movement being used (at least at present) by...

  • Manual SMT Pick and Place Machine
  • Instructions     from Manual SMT Pick and Place Machine
  • License:Creative Commons Attribution-ShareAlike 4.0 International Public LicenseBy exercising the Licensed Rights (defined below), You accept and agree to be bound by the terms and conditions of this Creative Commons Attribution-ShareAlike 4.0 International...

  • Electro-Magnetic Enabled Bagpipes
  • Instructions     from Electro-Magnetic Enabled Bagpipes
  • License:Creative Commons Attribution-ShareAlike 4.0 International Public LicenseBy exercising the Licensed Rights (defined below), You accept and agree to be bound by the terms and conditions of this Creative Commons Attribution-ShareAlike 4.0 International...

  • Arduino GPRS IOT Weather Station
  • Instructions     from Arduino GPRS IOT Weather Station
  • License:Creative Commons Attribution-ShareAlike 4.0 International Public LicenseBy exercising the Licensed Rights (defined below), You accept and agree to be bound by the terms and conditions of this Creative Commons Attribution-ShareAlike 4.0 International...

  • pi2meter
  • Instructions     from pi2meter
  • FINDING THE RESISTOR VALUESolder a 10K resistor to the Zero's header connector hole at pin 12, and connect the other end to the meter plus terminal. The meter minus terminal is connected to pin 14. To test it type the following: sudo gpio -g mode 18...

  • Data acquisition, and labelling
  • Instructions     from Smart HVAC System
  • Open studio.edgeimpulse.com , login (or create an account first) then create a new project. Choose Images project option, then Classify Multiple Objects. In Dashboard > Project Info, choose Bounding Boxes for labelling method and Nicla Vision for target...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday