10946 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Adjust the trimpots for gas measurements
Instructions from Solar Powered Air Quality Monitoring Station (IoT)
Move everything inside the box and adjust the trimpots to calibrate the measurements.Precise calibration wihout a known concentration of each gas is not possible, however the datasheet of the sensor recommends to calibrate the output to 2.5V and you...

Test the X, Y, Z motors and end stops.
Instructions from DuePrint
If everything worked correctly you should now have control of the movement motors and end stops. Manually move the print head to the center of the printer. Next, the axes homing will be tested to ensure the motors are wired up correctly. Be prepared...

Testing the right distances and positions
Instructions from Hedge Watcher
Now it is time to take a look through the transparent screen, adjust its angle, and check for the image of the small screen...Is it big enough? If not, you can try adding another Fresnel lens or moving the screen more to the front. [our physics teachers...

Connections
Instructions from Bunny Jump - Severe Jeans
Make sure that every pin inside of the Arduino is used correctly and setup well, certain pins reference things like the code or the button. You also have to make sure that everything works and is connected properly. Also check that the board and...

Packing
Instructions from Airwave Inspector
Fit everything back inside in the same way as from the test fit. Make sure to zip tie or hotglue down wires and cables so they don't interfere with the fans.Using adhesive to keep parts in position is also probably a good idea.Make sure to keep the power...

Carefully re-assemble
Instructions from Tiller Autopilot Limit Switches
Replace the controller PCB and check all its connectors are seated properly.Check again that there are no pinched wires and that everything can move freely.replace the watertight seal, clean and grease this with silicone grease if needed.Replace the...

Assembly Process
Instructions from DIY Digital Watch Project
The holder part is added from the bottom side of the frame after the top part has been assembled onto the watch frame. Two M2 screws are used to secure everything in place

Put Everything Back Together and Connect the MP3 Module, Cat Feeder PCB Override and Motion Detector to the Raspberry Pi
Instructions from Magic Flute of Rat Mind Control w/ Raspberry Pi
The automatic cat feeder PCB, DFPlayer module and motion detector should be connected to Raspberry Pi as directed above. You don't need to power the feeder PCB and everything else runs on 5v so just connect the motion detector and DFPlayer to the 5v...

Prerequisites
Instructions from Tyhac covid-19 audio diagnostic stack
Before we get too far into the build be sure to review the BoM (bill of materials) and make sure you have the required hardware. Apart from the physical hardware components you will need an AWS account, this is required for the cloud services provisioned...

JudgeTron 9001
Instructions from JudgeTron 9001
Okay, what does a JudgeTron need? My idea was to use neural networks embedded in biological units to do the whole judging thing. These biological units unfortunately don't have native electrical interfaces: I couldn't just put a RJ45 into them and have...

Step 3: Let's Connect Everything
Instructions from Smart Bluetooth Speaker with Spectrum Analyzer
The Bluetooth module is the F6188 module which is good and works very well. You might need to add a heatsink on top of the module as it heats up sometimes. The speakers are connected to PAM 8403 module and input to the module is given by the both...

Making Sure Everything is working
Instructions from UnifiedWater
It took me a long while to get things started. There was a lot of editing of libraries and Googling involved as documentation around connectivity was really limited to that one example above. But in the end everything worked. Below are some basic troubleshooting...

Chip timing for every running club!
Instructions from Chip timing for every running club!
First step is to make sure you get all the hardware in your hands (we bought everything from eBay):- One FRDM-K64F development kit from Freescale OR any other microcontroller platform capable of talking external devices (in that case you may need to...

Cypress PSOC 4 + ESP8266 WS2812 RGB XMAS Lights
Instructions from Cypress PSOC 4 + ESP8266 WS2812 RGB XMAS Lights
Use P3_0 and P3_1 to communicate with the ESP8266 RX/TX via a 5v<>3.3v shifter., add UART component and config to 11500kbps, 1024 rx buffer, 128 tx buffer (or less) default everything else.Add a X to 3.3V VREG and power the ESP8266 and level shifter.Make...

NeuroBytes
Instructions from NeuroBytes
Reflow.I use a modified toaster oven to reflow NeuroBytes, usually 8 or 12 at a time. It's not perfect; I usually watch the parts through the oven's window and sometimes need to manually extend the cycle to ensure everything reflows properly. I also...

|<
<
3
4
5
6
7
>
>|