2002 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 쓰리아워ㅾ Йlife강남술집정보ħ쓰리아워레깅스룸강남쓰리아워７┢강남술집정보indignation 쓰리아워레깅스룸ケ쓰리아워ı㎃outside"

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

Smart Power Sockets
Instructions from Smart Power Sockets
Now you can turn on and off from any browser. Prota OS supports remote access so you can control your appliances even when you are outside of your home network.

Step 3: Drill the float box
Instructions from "Mercator Origins": Sat Nav & Telemetry for Divers
Drill using a 6mm bit from the outside of the base of the IP67 float box through to the inside, aiming for the centre of the base of the box. 100mm x 60mm offset.

Raspberry Pi Zero W desk clock
Instructions from Raspberry Pi Zero W desk clock
Place the back panel writing-side down on a flat surface. Thread the 4 1" bolts through the corners from the bottom (the outside of the finished case). On the bolt nearest the GPIO header cut-out, place the 3/16" standoff and on the other four, place...

Step 27: Drill navigation pod for wet link penetrator
Instructions from "Mercator Origins": Sat Nav & Telemetry for Divers
Drill a 6mm hole (recommend using a stepped drill bit) at a position 20mm x 20mm from the top and right sides of the door of the enclosure, viewed from the back. Drill from the outside of the enclosure to the inside. (Photo taken later in the build process,...

Step 28: Drill hole for depth sensor
Instructions from "Mercator Origins": Sat Nav & Telemetry for Divers
Drill a 10mm hole (recommend using a stepped drill bit) at a position 20mm x 20mm from the top and left sides of the door of the enclosure, viewed from the back. Drill from the outside of the enclosure to the inside. (Photo taken later in the build process,...

Dtto - Explorer Modular Robot
Instructions from Dtto - Explorer Modular Robot
We need:- 1 x Part 006-1- 1 x Part 008-1- 1 x Part 010-1- 12 x Neodymium MagnetsAs we did in the previous step, we will put the magnets in the female parts. Now, remember to put all magnets with the north pole facing the outside of the module. If we...

A "Quick 220" clone
Instructions from A "Quick 220" clone
Prepare the chassis.Drill a hole centered in each of the two "short" sides of the case sized for the CG-16 cable gland. Drill a hole sized for the L6-20 receptacle. The hole should be centered horizontally on the panel, but the top edge should be as...

Launching Stepmania
Instructions from Stepmania 5 compile for ARM (Jetson TK1)
1. Launching Stepmania in X outside of desktop: sudo service lightdm stop xinit /home/ubuntu/stepmania-src/stepmania -- :9 2. Launching with launcher.sh that pauses for Sound Manager to finish init (TK1-specific, placed the following in launcher.sh):...

ROSCOE - A Scalable, Platform Independent Robot
Instructions from ROSCOE - A Scalable, Platform Independent Robot
Mechanical:For stabilization of wheels a carriage is constructed consisting of 5/8" stainless all-thread and a 16 inch BMX bike fork. 1) Drill 2 3/8" holes 1" from each end of the steerer tube.2) Bisect the fork longitudinally along the steerer...

Connect the limit switches
Instructions from CNC retrofit with a Buildbotics CNC Controller
The Dyna is equipped with three limit switches; one on each axis. These limit switches are used for homing the machine. This picture shows the z-axis limit switch. When the two parts of the limit switch come together, the z-axis is at its...

Switch-pipe adapter
Instructions from Electro Knife for Simulated Combat EleKSCo
We will start with the most exotic component in the entire build because it requires a 3D printer. If you picked a pushbutton with an exceptionally long threaded shaft, you might be able to skip this and mount your switch directly onto a chunk of pipe,...

Lower fastenings - middle bed and capsule/habitat fastener
Instructions from Camperwagon 3.0 - Eljestmobile
The aim for this step is to provide lower support for the living area to rest on. For the back living area this will be placed inside the sliders fasten to the frame. The middle living area will be fasten around it and fasten to the slider (so it will...

Assembly of the case
Instructions from Adaptive wireless switch
Place pushbuttons into the two holes. The longer pushbutton belongs on the outer position (close to the edge of the case). Lift the controller off the table so the buttons are suspended by gravity. Rotate the buttons so the tabs are lined up with the...

Expansion
Instructions from RAK811 based LoRa Node powered by AA batteries
The prototyping area contains through hole soldering pads routed to all pins of RAK811 module, plus some small amount of free connected pads for prototyping. Connections for outside detachable sensors are provided via W,X,Y,Z screw terminals. If the...

1
2
3
4
5
>
>|