163 Results for "%E3%80%8A%EC%B5%9C%EC%A0%80%EA%B0%80 O1O%CE%9E5793%CE%9E7458%E3%80%8B %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%E3%86%8B %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%85%94%EC%B8%A0%EB%A3%B8applause%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%EC%8B%A0%EC%82%AC%EC%95%84%EC%9D%B4%EB%A6%B0%EC%A3%BC%EB%8C%80caught %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%E3%8F%87%E3%85%97%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0queer"

Sigma Derby Clone
Instructions from Sigma Derby Clone
Program odds display)The board will receive the same 5 digit signal as the other boards, and break out the first two digits to print the odds.Left 5 odds display:#include int h45odds = 0; int h35odds = 0; int h34odds = 0; int h25odds = 0; int h24odds...

▇▇▇▇ Code Solution ▇▇▇▇
Instructions from FPGA Boot Camp #4: State Machines
There are many possible solutions, of course, but here's mine. Let's break it down into manageable pieces. First, let's look at the housekeeping items. I mentioned a 12 MHz clock, although that's ugly for simulation. Because of that, I wrote two...

AIRee Pollution Clock
Instructions from AIRee
#include #ifdef __AVR__ #include #endif // Which pin on the Arduino is connected to the NeoPixels? // On a Trinket or Gemma we suggest changing this to 1 #define PIN 6 // How many NeoPixels are attached to the Arduino? #define NUMPIXELS 48 // How much...

▇▇▇▇ State Implementation ▇▇▇▇
Instructions from FPGA Boot Camp #4: State Machines
When creating a state machine, there are two things to consider: How to represent the state you are currently in is the most obvious one. This may seem like a trivial concern, but as you'll see, there is more to it than meets the eye. The second decision...

Connecting the wires
Instructions from ZX Spectrum Expansion Port EEPROM Interface
ZX EEPROMMemrq -> oeA0-A13 -> A0-A13D0-D7 -> D0-D75v/gnd -> 5v/gndPull the eeprom we and a14 high. Connect the the zx a14 and a15 to pin 1 and 2 of the 74ls32 then pin 3 to ce pin of the eeprom. Also Connect the...

Front end assembly
Instructions from OSUG: Open-Source Underwater Glider
Place a single 608ZZ bearing in each of “Syringe_clamp_front” and “Syringe_clamp_back” On the “Syringe_clamp_back” secure the bearing in place with the “Engine_bearing_fastener” piece, 3 M3 20mm...

rDUINOScope Boiana
Instructions from rDUINOScope Boiana
TEP 3 AssembleFor more detailed instructions, please visit the Project Website : http://rduinoscope.co.nf/rDUINO_step3.htmlNow is the time to create the Shield board. A Shield board is a board with pinouts which you stack on top of the ArduinoDUE board.Some...

Print parts
Instructions from Zvychai One
No step-by-step instructions here, follow your printing intuition/experience, but few tips would be: I'd say print everything except small covers with 3-4 walls and 30-40% infill. Most parts do not require much printing support except maybe if you have...

The Talking Microtronic Computer System Emulator
Instructions from The Talking Microtronic Computer System Emulator
Set up the hardware - the emulator main sketch shows the pin layout: // // SD+Ethernet Shield (optional) // #if defined (SDCARD) #define SDCARD_CHIP_SELECT 4 // // software serial interface for Emic 2 TTS module (optional) // #if defined (SPEECH) #define...

Main Wiring
Instructions from Capacitive Gamepad
Connect MPR121 to arudino i2c and power. On a Micro this is pins 2&3 plus VCC and GND. Flash the arduino and make sure everything works as you like. Breaking out the RST pin to a tactile switch is probably unnecessary, i've had no problem re-flashing...

Cuts required
Instructions from The Learner's Heliostat
The plywood product I used was 1/2x2x4 G1S, $37 ea before tax in Ontario in summer of 2022. For the project infrastructure, four 1" x 4" x 8' knotty pine planks would be price competitive and less work to waterproof, but less convenient to transport....

▇▇▇▇ D Flip Flops ▇▇▇▇
Instructions from FPGA Bootcamp #0
The SR latch modified with the inverter is often called a D latch because the single input is data for the latch to store. To make it a D flip flop, though, you need to arrange to capture the data at a clock edge, not just any time the latch is enabled....

Assembly Code
Instructions from 8051 Alarm Clock
ROA EQU 7FH ;es Reloj o es Alarma USR EQU 50H ;Unidades de Segundos del Reloj DSR EQU 51H ;Decenas de Segundos del Reloj UMR EQU 52H ;Unidades de Minutos del Reloj DMR EQU 53H ;Decenas de Minutos del Reloj UHR EQU 54H ;Unidades de Horas del...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
I attached a 2 axis gyroscope and 3 axis accelerometer onto this project so that I could add some interesting control to the device. The 5 degrees of freedom board from Sparkfun outputs data from its gyroscope and accelerometer as analog voltages. I...

Circuit Connection:
Instructions from DIY Arduino Tic Toc Toe Game
Connect the push buttons keypad to Arduino Uno as shown in circuit diagram.(R1~A0,R2~A1,R3~A2,R4~A3,C1~A4,C2~A5,C3~Pin 2,C4~Pin 3).Also take a extra push button(Reset Button) and connect to Arduino.(Reset,GND).Connect all the pixel LEDs.(-Ve/GND~GND,+Ve/5V~5V,Data...

|<
<
1
2
3
4
5
>
>|