Close

436 Results for "fix"

  • Trombino
  • Instructions     from Trombino
  • Drill two holes in the lower half of theArduino box and fix it to the top of the potentiometer housing. Thread wires through the holes. Add in the Arduino, ethernet shield and breadboard and hook up the parts currently attached to the housing. Open up...

  • Portable environmental monitor
  • Instructions     from Portable environmental monitor
  • Solder the Mics-vz-89T . Make sure you're wearing gloves, and that no soldering fumes, grease or dirt contaminates the sensor board. Once done, mount the PCB in the enclosureFix the ILI9341 LCD on top, in the designated area, and carefully connect the...

  • RaspiTrap V1.0
  • Instructions     from RaspiTrap V1.0
  • Transmitter and ReceiverTo fix the IR sensors TEMIC K153P inside the trap, I manually milled two grooves.They were placed behind the 3mm acrylic glass plates.As you can see, the 9gr. servo motor is already mounted.

  • Dtto - Explorer Modular Robot
  • Instructions     from Dtto - Explorer Modular Robot
  • We need:- 2 x Part 004-1- 2 x MG92B Servomotors (step 3)In this step we are going to fix the motors to the printed parts. The motor should fit correctly. We can use the screws that come with the motor, but we will have to cut them to the right length....

  • Linear Delta Robot 3D printed
  • Instructions     from Linear Delta Robot 3D printed
  • Print the .stl files preferrably without brims, they are difficult to remove. It may be necessary to sand the beams in order to fit.Please inform me if the .stl files are not in the correct size....When constructing, set the servo's in the middle position,...

  • How To Make A Smart Clock
  • Instructions     from How To Make A Smart Clock
  • Production of screenCut the black acrylic transparent board into the inner size of the shell cover (it is laborious and takes me about 20 minutes), as shown below:Sorry, I forgot to take pictures in the future steps, and have to use the pictures taken...

  • 1. Hand soldering the pin
  • Instructions     from K.I.T.T. - KNIGHT RIDER badge/brooch
  • Add solder to one pad, use pliers to hold the hin in place and solder everything together. After that use heat the second pad and the clip simultaneously and add solder to fix up the second pad. You need to start with the clip because it takes a lot...

  • The Problem
  • Instructions     from Vision-Based Grasp Learning for Prosthetics
  • The tendons in the transmission system are subject to wear and tear and tend to snap at some point (believe it or not, one of the tendons in the middle finger broke 5 minutes before my Viva, giving my examiners the finger). Today we are going to fix...

  • BrailleRap STEAM CNC
  • Instructions     from BrailleRap STEAM CNC
  • 3. Fix the material on which you wish to print braille on an MDF wood sheet with a tape and place it under the nail. We’ve used a 180 GSM drawing paper of dimensions 200 X 200 mm.

  • Make your enclosure
  • Instructions     from Cat Detector - Useless Machine
  • I made my enclosure using scrap plastic. I cut out (2) 2"x4" pieces and (2) 4"x3" pieces. I used a medium body solvent glue to fix these into a 4-sided box. You could just as easily use cardboard, wood, or whatever you feel like to hold your project....

  • Placing the Arduino and EMIC
  • Instructions     from Eye-to-Speech Module
  • In this step you have to place the Arduino and the EMIC on the board. Make sure to place the two parts gently and then fix them with a rubber band. Click here to go to the corresponding part of our video.
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday