385 Results for "%E3%80%8A%EB%AC%B8%EC%9D%98OIO%E2%96%B35793%E2%86%977458%E3%80%8B%EA%B0%95%EB%82%A8%EB%9E%80%EC%A0%9C%EB%A6%AC%E3%82%84%E2%88%ABfall%EA%B0%95%EB%82%A8%EB%A3%B8%E3%8E%94%EC%84%A0%EB%A6%89%EB%9E%80%EC%A0%9C%EB%A6%AC%EA%B0%95%EB%82%A8%EB%9E%80%EC%A0%9C%EB%A6%AC%EB%A3%B8%E3%85%94 %E2%92%AF%EA%B0%95%EB%82%A8%EB%9E%80%EC%A0%9C%EB%A6%AC%EB%A3%B8eldest %EC%84%A0%EB%A6%89%EB%9E%80%EC%A0%9C%EB%A6%AC%EB%A3%B8%E2%93%A1%EC%84%A0%EB%A6%89%EB%9E%80%EC%A0%9C%EB%A6%AC%E2%96%A1%E3%83%A4gloom"

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

Pedal Wiring
Instructions from Pedalino™
Pedalino is designed to work with the majority of expression pedals on the market, but there are a few popular pedal types which are incompatible and need to use adapters in order to work with Pedalino. There is no recognized standard for footswitch...

[2016] InternetS of Energy - Call me DAISEE
Instructions from [2016] InternetS of Energy - Call me DAISEE
Ethereum installation on a Raspberry PIAn Ethereum node running on a Raspberry Pi. Photo by RIeul (CC-BY-NC-SA) Equipment 3 Raspberry Pi with Ethereum client (each Pi = a node of a blockchain) 3 SD cards 2 computers Other solution Using Wio Link to simulate...

JeremFuge (a.k.a. LC-LE:fuge)
Instructions from JeremFuge (a.k.a. LC-LE:fuge)
Here below are all the connections for the JeremFuge. We describe them cable per cable with each time the beginning and the end of the cable.The breadboard is welded on the Arduino Uno.Connections Breadboard : Arduino UnoA : DigitalA2 to A7 : 2 to 7...

Cree Dimming Level
Instructions from Cree Dimming Level
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

Run a Code
Instructions from AC Voltmeter using Arduino
int m; // initialise variable m float n; //initialise variable n void setup() { pinMode(A0,INPUT); // set pin a0 as input pin Serial.begin(9600);// begin serial communication between Arduino and pc } void loop() { m=analogRead(A0); // read analog values...

Header Pins
Instructions from Sig7Seg - controller for mechanical 7 segment
Solder on the 3 sets of three pin headers for the i2c address (A0, A1, and A2). You'll need to attach a jumper to each one to pull the pin high or low (chip will not work if these are left floating). The remaining header pins are optional depending...

Connect to Arduino
Instructions from 4-Channel Optogenetics Pulser
Plug the collated ground wires into an Arduino Ground pin, and the collated +5V wires into a +5V pin (if using a Due, use the +3.3V pin or you will damage the microcontroller) and plug the other jumper wires into the correct I/O pins: Toggle switches...

NANO-4096
Instructions from NANO-4096
Finally screw the spacer onto the joystick breakout boardSolder the joystick onto the perfboard and connect VCC (5v) and GNDConnect the X pot to A1 (Since the board is rotated X becomes Y)Connect the Y pot to A0Key is not connected

Fan controller for Re:Load Pro
Instructions from Fan controller for Re:Load Pro
Make you the PCB and get the components and any standard 60mm 4-wire fan will probably do the job. I used a JMC "6015-12HB APW" that I had lying around. The exact the same fan is readily available on eBay.I used eagle to design my PCB, and the files...

Wire
Instructions from Hybrid Sim Yoke
Wire as follows: Both potentiometers Pin 1: 5v Both potentiometers Pin 3: ground Left potentiometer Pin 2: A0 Right potentiometer Pin 2: A3. Note that they have two channels, and all three wires have to connect to the same channel...

I2C Sensors and debugging
Instructions from Stratux ADSB Receiver and AHRS
I wanted to use a BMP280 I had in my parts bin for altitude measurements. I have used it in the past for a simple weather station and it works great! Turns out, it is even the go to sensor for Stratux, so I went ahead and plugged it in, activated it...

Circuit Connection:
Instructions from DIY Arduino Tic Toc Toe Game
Connect the push buttons keypad to Arduino Uno as shown in circuit diagram.(R1~A0,R2~A1,R3~A2,R4~A3,C1~A4,C2~A5,C3~Pin 2,C4~Pin 3).Also take a extra push button(Reset Button) and connect to Arduino.(Reset,GND).Connect all the pixel LEDs.(-Ve/GND~GND,+Ve/5V~5V,Data...

Run a Program
Instructions from IoT Digital Thermometer using LM35 and NodeMCU
#include const char* ssid = "*********"; // Your ssid const char* password = "***********"; // Your Password float temp_celsius = 0; float temp_fahrenheit = 0; WiFiServer server(80); void setup() { Serial.begin(115200); pinMode(A0, INPUT); Serial.println();...

Soldering the CPU
Instructions from 68020 minimal homebrew computer
Start by soldering the CPU; it can be done with a regular soldering iron. Refer to the internet for guidance on soldering this SMD component (SMD soldering tutorial). The trick is to use flux (and very little tin). For me, this was the first time I soldered...

1
2
3
4
5
>
>|