1565 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》강남레깅스룸ⓨ강남레깅스룸singing강남레깅스강남레깅스룸강남레깅스룸remainder 강남레깅스㉮┢선릉레깅스agitation"

HandBot
Instructions from HandBot
Once you have the correct programming of what will be the engine performance you need review the functioning and values of the MPU-6050 accelerometer. The X and Y axes are as the device is marked on the card.VCC to 5V pin.GND to GND pin.SCL to A5 pin.SDA...

LoFi
Instructions from LoFi
Repeat steps 9-14 for the LoFi Gateway board.

Motorised Z-Table Controller
Instructions from Motorised Z-Table Controller
Cut out or have board made.Install 4 x 0805 10K resistors on inputs, add 1 0603 1uF cap , solder in ATTINY 2313, add headers.Switch is optional, doesn't do anything in code yet.Program it! Wire in 5V power and switches, connect PUL to Pulse Input, DIR...

Bluetooth Arcade Controller
Instructions from Bluetooth Arcade Controller
Get all your bits and pieces together.The gerber files I used are in github (https://github.com/wannabeerased/arcadeadapter). I used http://dirtypcbs.com/ to have them made up, at the time it cost me $14 for 10 PCBs delivered.Try to get a right...

The world's first paper quadcopter
Instructions from The world's first paper quadcopter
Get a piece of 3.5 x 8.5 form board or or you can use cardboard if you use cardboard you will need 2 3.5 x 8.5 just glue them together to make one solid piece.Lay the short tubes on the sides of the board and the long tubes across the top to form the...

Infinity Mirror Clock
Instructions from Infinity Mirror Clock
The clock is primarily made up of the following: 2 pieces of 8mm plywood (600mm x 600mm) - needs to be cut as per the schematic above1 piece of 18mm block-board (600mm x 600mm) - needs to be cut as per the schematic above. Please be careful with the...

1Charger
Instructions from 1Charger
Calibrate connected-ish ( serial port )The serial port is useful for making charge curves and debug. I use a usb to serial cable that accept 3.3v level.Connect the serial cable to GND and pin PA7The software UART timer interrupt is also used as a timebase....

3D(ollar) Scanner
Instructions from 3D(ollar) Scanner
8. Take picture using program local to OS: -use GIMP or other program to find pixels and locate coordinates for center of platter-set resolution in the video_line_viewer to the size your camera outputs.. manually :(-determine angle, in radians of platter...

Modular Clock Kit
Instructions from Modular Clock Kit
The Clock Logic board is 3.75" x 2.50".The I.C.s are spaced two (2) rows apart.I started on one end with the simple power supply, wave shaper and divide by 60 circuits.Next is the inter-stage logic. The heart of the clock.The various resets, divide by...

Arduino Game Console - the BlueOkiris Gameduino
Instructions from Arduino Game Console - the BlueOkiris Gameduino
Take the analog stick and solder the appropriate wires to it. Place ground to ground, 5v to 5v, x to A4, and y to A5. Again do not use male ends to the arduino.

Poster VU
Instructions from Poster VU
Measure the inside of the poster frame and cut 30 ((6 + 9) x 2) dividers from the foam art board to fit perfectly between each strip and each row of LEDs inside the posters. Cut notches the width of the foam board and half-way deep at each intersection...

Bored No More
Instructions from Bored No More
Dream It!Inspiration Google search on science fair boardsI used Google image search to look at what other projects looked like. There were some real good looking projects but little innovation in the boards themselves.It is time to break away from...

Bored No More
Instructions from Bored No More
Customize Tri-Fold Board Part 1Foam core partsPicture wheelThe picture wheel will go in the middle section of the tri-fold board so I measured that and made the wheel as large as I could. To cut the wheel I used a small nail pushed through the...

FarmBot - Open-Source CNC Farming
Instructions from FarmBot - Open-Source CNC Farming
Supporting InfrastructureFarmBot Tracks need to be attached to supporting infrastructure. Where you decide to install your FarmBot will determine how you setup your Tracks and therefor what supporting infrastructure you need. You might attach your track...

FarmBot - Open-Source CNC Farming
Instructions from FarmBot - Open-Source CNC Farming
Assembly PreparationIn order to shorten the time it takes for you to assemble your FarmBot hardware, follow these preliminary steps. 15 minutesThis is the estimated time it will take for assembly preparation.Organize your PartsWhen you first open up...

|<
<
2
3
4
5
6
>
>|