Results for %EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%EA%B0%95%EC%B6%94%E2%9C%9Awww%2Coptime4.com%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%20%EC%9D%B8%EC%B2%9C%EB%A7%88%EC%82%AC%EC%A7%80%20%E2%9C%9A%20%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%E1%98%9B%20%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%EC%82%AC%EC%A7%84%E1%98%9B%20%EC%9D%B8%EC%B2%9C%ED%9C%B4%EA%B2%8C%ED%85%94%20%EC%9D%B8%EC%B2%9C%ED%82%A4%EC%8A%A4%EB%B0%A9%20%ED%83%80%EC%9E%84

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

Step 20: Gather components for sub-sea cable
Instructions from "Mercator Origins": Sat Nav & Telemetry for Divers
Components: Blue Robotics 4-core Ping Cable (11 metres), 2 x 4.5mm WLP-M06 cable wet link penetrators including nuts, o-rings, and silicone seal, plus 2 x cut shake-proof washers, 1 x rubber strain relief boot , 2 x Micro JST 2-way female connectors....

Joy232
Instructions from Joy232
Loading the Hook Code In order to use Joy232 it is necessary to load it on the MSX by either of the methods presented below.Method 1: Copy the file "joy232.bin" to a floppy disk (or an equivalent option like the SD Mapper interface. load and execute...

NODE-RED CONNECTIONS!
Instructions from OBS_IRL_STREAM_DECK
The first thing we need is a basic flow to separate button presses into different outputs. [{"id":"50b49ab2.1e6f64","type":"mqtt in","z":"7805686.aa4fd98","name":"","topic":"button_glove","qos":"0","datatype":"auto","broker":"","x":310,"y":2180,"wires":[["ea9f502f.2dd17"]]},{"id":"ea9f502f.2dd17","type":"json","z":"7805686.aa4fd98","name":"","property":"payload","action":"obj","pretty":false,"x":490,"y":2180,"wires":[["425aef92.aa3da8"]]},{"id":"425aef92.aa3da8","type":"function","z":"7805686.aa4fd98","name":"ButtonSeperator","func":"var...

Cree Dimming Level
Instructions from Cree Dimming Level
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

Cabling the MPE device's hardware-components
Instructions from MPE-DIY-Device
Power supply: Ground - GND from Teensy (power-rail as described in the PDF attached) +3.3V - 3.3V from Teensy (power-rail as described in the PDF attached) Joystick 1: VRx - Pin 23/A9 (horizontal control) VRy - Pin 22/A8 (vertical control) SW - Pin 01...

Address Bus
Instructions from L-Star: Software-Defined 6502 Computer
This last step is going to get REALLY tedious because the Address Bus has so many lines. But this is the last step and you should be done, so keep it up just a little longer. A0: 6502 Pin 9 to FLiP pin 13 A1: 6502 Pin 10 to FLiP pin 14 A2: 6502...

Assemble your Extruder
Instructions from The Trash Printer - Version 3
First, let's assemble the extruder, so we can just drop it onto the printer later! There are two sets of spacers, labeled B1-B7 for the Bottom assembly, and T1-T2 for the top assembly. There is also an extruder motor shaft coupler spacer, labeled...

CH Products Trackball Pro USB modding
Instructions from CH Products Trackball Pro USB modding
Connect your BUS MOUSE pins to the following pins of your Arduino Pro Micro:Gnd : GroundVcc : Vcc (+5V)Port D3 : X axis encoder / channel APort D2 : X axis encoder / channel BPort D1 : Y axis encoder / channel APort D0 : Y axis encoder / channel BPort...

Resource Monitor
Instructions from Resource Monitor
Solder wires from UBBB to LCD. (Note that uBBB pins are ordered as if looking at the bottom, since it also serves as a generic 32-TQFP breakout board if you flip it upside down). Specific connections are described below:-Connect pins 1, 5, and 16 on...

Arduino Code
Instructions from OBS_IRL_STREAM_DECK
It's in the GITHUB! The code comes down the these smaller steps: MQTT handling and Button handling. Let's do button handling first. I made a simple button object with the pin number, button press boolean, and button count. struct Button { const uint8_t...

Software
Instructions from Mike's Robot Dog
Making the dog walk is quite the challenge, so here's my approach. I created a drawing showing "standing" leg positions in black and progressive changes in red. The approach is to: 1) lift the left front and right rear legs 2) move the left front and...

Trinket LED Thermometer
Instructions from Trinket LED Thermometer
Here's a functional program to initialize the hardware, read temps, and display temps as colors. Enhancements such as multiple sensors/LEDs per Trinket are possible but left as an exercise for the reader./* trinket_thermo ---------------------------------------------------------------------------------...

Affordable Reflectance Transformation Imaging Dome
Instructions from Affordable Reflectance Transformation Imaging Dome
Time to start putting together the low-side driver board with the CAT4101s. First step is to install the connector on the 11 x 8.5 cm protoboard. This is the spec'ed component, but if you can't find one that size, you can use another one up to 11.5 cm...

Arduino Game Console - the BlueOkiris Gameduino
Instructions from Arduino Game Console - the BlueOkiris Gameduino
Take the analog stick and solder the appropriate wires to it. Place ground to ground, 5v to 5v, x to A4, and y to A5. Again do not use male ends to the arduino.