179 Results for "solder fume extractor"

Solder the first components
Instructions from 68020 minimal homebrew computer
Create a custom socket for the X-tal oscillator from some female pinheads.Solder the 74HC14.Solder the optional power supply.Solder the power LED/resistor.Solder the power switch / header.Solder the decoupling capacitors (100 nF) around the chips.Solder...

Solder everything together
Instructions from Reimagining Duo Pop
1. Use the reference picture and wiring diagrams below to solder all the pieces. Your finish product may not look like mine and that is okay. Wire it in the most convenient method. I measured each wire cut and stripped the ends and then soldered them...

Solder on the Headers
Instructions from Autonomous Agri-robot Control System
The headers for the Nanos, compass, Ublox, Emic TFT and SIM800 are all standard male - female 0.1" pitch and are relatively easy to solder - so do these first. The main 2 MCUs push onto the underside of the PCB and the headers for the MEGA 2560...

Solder wires to the controls
Instructions from Turnado Hardware MIDI Controller
Solder wires to the following control pins: Joystick modules:X GND VCCSwitched rotary encoders: Pin A (left pin of 3-set) Pin B (right pin of 3-set) Switch (either pin of the 2-set)GND 1 (centre pin of 3-set)GND 2 (remaining...

Solder speaker and power right angle pin headers
Instructions from Stylish!
They all take 2 x 1 pin angled pinheaders. The battery connectors point away from the speaker. The speaker connector points straight down.

Solder X wires between FPC breakout board to the Microcontroller.
Instructions from QMK Powered Laptop Keyboard
For me X = 24. and i had poor experience with digital pin 33 and digital pin 25. this is attributed to set up issues which i am not sure how to solve so i just switched pins.i used wire wrapping wire for this, as i wanted to maintain flexibility and...

Solder WS2812B RGB LEDS, or 4 x 1 female pinheader for external LED ring
Instructions from Stylish!
If you are not using an external LED ring, you'll have to solder the surface mount WS2812B RGB LEDs by hand. I think it works best if you use lots of flux, get the part into place, and then hit it with solder. Be aware of the corner with the notch...

Step 22: Solder the Micro JST female connectors to the sub-sea cable
Instructions from "Mercator Origins": Sat Nav & Telemetry for Divers
Prepare the float box end of the sub-sea cable by soldering 2 x 2-way Micro JST female connectors to the 4-core cable. Ensure the wire colours correspond to the connections made in Step 5. Plug 1 corresponds to Socket 1 and Plug 2 corresponds to Socket...

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Solder the 2 x 22pF Supporting Capacitors for the Crystal Oscillator

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Solder the 3 x 220 Ohm Resistors (the 3 resistor spots nearest to the Crystal Oscillator)

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Solder 3 x 3mm LEDs (Top is Yellow, Bottom Left is Red, Bottom Right is Green)

Integrate seamlessly into a breadboard setup
Instructions from 28-Pin SOP Protoboard
Solder five 1 x 14 white single-row female headers to columns A-JSolder two single-row 1x14 red headers (male or female) onto the positive columns of the power bus.Solder two single-row 1x14 black headers (male or female) onto the negative columns of...

Back To The Future Time Circuit Clock
Instructions from Back To The Future Time Circuit Clock
Create (etch and solder) 5 PCB from big-module-shift and big-module-test - those are the display PCBs and drivers for 14-segment displays.

Back To The Future Time Circuit Clock
Instructions from Back To The Future Time Circuit Clock
Solder display PCBs to display driver PCBs using angular pin headers and in case of 14-segments, an additional ribbon cable connection is required.

Evaluate your PCB surface mount soldering/reflow equipment
Instructions from TinyFPGA A-Series
The FPGA for these boards is in a QFN32 package which is possible, but very difficult to solder with an iron. It is much easier to use the solder paste reflow method to assemble these boards.The following tools and supplies will be necessary to reflow...

1
2
3
4
5
>
>|