1831 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 쓰리아워가격ｕ 쓰리아워가격earth강남쓰리아워강남쓰리아워쓰리아워enter 강남쓰리아워ぶЪ강남쓰리아워most"

Open Source Science Tricorder
Instructions from Open Source Science Tricorder
Step 1: Motherboard Assembly and ProgrammingI designed all of the boards to be hand solder friendly, with leadless QFNs all on one side (that can be reflowed). If the other side has components, these are usually larger and easier to hand solder. Step...

Open Source Science Tricorder
Instructions from Open Source Science Tricorder
http://www.tricorderproject.org/arducorder/chipkit-mplab-ide-0023-arducorder.ziphttp://www.tricorderproject.org/arducorder/chipkit-mplab-ide-0023-arducorder.zipStep 3: Constructing the CaseThis beautiful case is constructed from laser cut acrylic --...

ZRTP Hardphone
Instructions from ZRTP Hardphone
### [ WRITE IMAGE TO SD ]wget "http://93.174.101.10/bt/09bc05ab03780f279390e9cf6a15c7c249f712e1/data/2014-01-07-wheezy-raspbian.zip"7z x 2014-01-07-wheezy-raspbian.zipSD_CARD=/dev/sdX # Change it to your SD card device namemd5sum 2014-01-07-wheezy-raspbian.img...

ZRTP Hardphone
Instructions from ZRTP Hardphone
### [ UPDATING FIRMWARE ]aptitude install -y git-core curl binutilswget https://raw.github.com/Hexxeh/rpi-update/master/rpi-update -O /usr/bin/rpi-update && chmod +x /usr/bin/rpi-updaterpi-updatereboot### [ END UPDATING FIRMWARE ]

Antares: Linux kernel-like buildsystem for uCs
Instructions from Antares: Linux kernel-like buildsystem for uCs
Install dependencies: git, GNU/make, gcc, flex, bison, gperfDebian/ubuntu: sudo apt-get install build-essential git flex bison gperfArch Linux: sudo pacman -S git flex bison gperfOS X: brew install coreutils git make

HandBot
Instructions from HandBot
Once you have the correct programming of what will be the engine performance you need review the functioning and values of the MPU-6050 accelerometer. The X and Y axes are as the device is marked on the card.VCC to 5V pin.GND to GND pin.SCL to A5 pin.SDA...

LoFi
Instructions from LoFi
On that same window (Device Programming), click Fuses. All but two of the fuses are factory default.Scroll until you see BODLEVEL and SUT_CKSEL. Set them to 1V8 and blah_blah_blah_4MS, respectively. If you are going to be using a wired power supply or...

LoFi
Instructions from LoFi
On that same window (Device Programming), click Production file. Browse to the Release\LoFi.elf file and check the Flash checkbox to enable the Program button.Click the Program button to write the object code to the ATtiny84A on the LoFi Sender board....

LoFi
Instructions from LoFi
Repeat steps 9-14 for the LoFi Gateway board.

Motorised Z-Table Controller
Instructions from Motorised Z-Table Controller
Cut out or have board made.Install 4 x 0805 10K resistors on inputs, add 1 0603 1uF cap , solder in ATTINY 2313, add headers.Switch is optional, doesn't do anything in code yet.Program it! Wire in 5V power and switches, connect PUL to Pulse Input, DIR...

Bluetooth Arcade Controller
Instructions from Bluetooth Arcade Controller
Get all your bits and pieces together.The gerber files I used are in github (https://github.com/wannabeerased/arcadeadapter). I used http://dirtypcbs.com/ to have them made up, at the time it cost me $14 for 10 PCBs delivered.Try to get a right...

The world's first paper quadcopter
Instructions from The world's first paper quadcopter
Get a piece of 3.5 x 8.5 form board or or you can use cardboard if you use cardboard you will need 2 3.5 x 8.5 just glue them together to make one solid piece.Lay the short tubes on the sides of the board and the long tubes across the top to form the...

Daisy Kite Airborne Wind Turbine
Instructions from Daisy Kite Airborne Wind Turbine
Read over this system design note...Daisy Project System DesignIntroductionThe Daisy project is an attempt to realize competitive open source airborne wind energy generation.Project Executive SummaryThe Daisy project is part of the rapid AWE development...

Lexitron RSS Reader
Instructions from Lexitron RSS Reader
Tickernut circuit design and hardware:Enclosure:The motherboard is shaped to fit tightly inside a standard ABS jiffy box which set its limited size. The box has cutouts to expose all motherboard connectors on the left side and a small speaker and antenna...

Lexitron RSS Reader
Instructions from Lexitron RSS Reader
Tickernut construction log:Construction was completed in stages over the period of many months with a design that evolved to suit the available parts. The progression of construction was arranged so that each stage could be completed and tested...

|<
<
2
3
4
5
6
>
>|