Close

739 Results for "%EA%B0%95%EB%82%A8%EC%98%A4%ED%94%BC%EB%A7%81%ED%81%AC%E2%9C%9Awww%2Coptime4.com%EA%B0%95%EB%82%A8%EC%98%A4%ED%94%BC %EA%B0%95%EB%82%A8%EB%A7%88%EC%82%AC%EC%A7%80 %E2%9C%9A %EA%B0%95%EB%82%A8%EC%98%A4%ED%94%BC%E1%98%AB %EA%B0%95%EB%82%A8%EC%98%A4%ED%94%BC%EC%82%AC%EC%A7%84%E1%98%AB %EA%B0%95%EB%82%A8%ED%9C%B4%EA%B2%8C%ED%85%94 %EA%B0%95%EB%82%A8%ED%82%A4%EC%8A%A4%EB%B0%A9 %ED%83%80%EC%9E%84"

  • Cree Dimming Level
  • Instructions     from Cree Dimming Level
  • Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

  • Solder the LiPo battery
  • Instructions     from Detective Boys walkie talkie pin badge
  • You will need a Lipo battery with 100mAh capacity, you can get a higher capacity one but take into account that more capacity means a bigger battery so it won't fit into the board, the battery must have a protection circuit included. The battery must...

  • Joy232
  • Instructions     from Joy232
  • Loading the Hook Code In order to use Joy232 it is necessary to load it on the MSX by either of the methods presented below.Method 1: Copy the file "joy232.bin" to a floppy disk (or an equivalent option like the SD Mapper interface. load and execute...

  • Cabling the MPE device's hardware-components
  • Instructions     from MPE-DIY-Device
  • Power supply: Ground - GND from Teensy (power-rail as described in the PDF attached) +3.3V - 3.3V from Teensy (power-rail as described in the PDF attached) Joystick 1: VRx - Pin 23/A9 (horizontal control) VRy - Pin 22/A8 (vertical control) SW - Pin 01...

  • Some notes
  • Instructions     from Hydroponics Sensor
  • The ESP-32 board pins operate in 3.3v levels while the Gravity pH and EC sensors operate in 5V. I inserted a simple voltage divider to shift 5v to 3.3v levels on the signal pins. 

  • Address Bus
  • Instructions     from L-Star: Software-Defined 6502 Computer
  • This last step is going to get REALLY tedious because the Address Bus has so many lines. But this is the last step and you should be done, so keep it up just a little longer. A0: 6502 Pin 9 to FLiP pin 13 A1: 6502 Pin 10 to FLiP pin 14 A2: 6502...

  • Pedal Wiring
  • Instructions     from Pedalino™
  • Pedalino is designed to work with the majority of expression pedals on the market, but there are a few popular pedal types which are incompatible and need to use adapters in order to work with Pedalino. There is no recognized standard for footswitch...

  • I2C Sensors and debugging
  • Instructions     from Stratux ADSB Receiver and AHRS
  • I wanted to use a BMP280 I had in my parts bin for altitude measurements. I have used it in the past for a simple weather station and it works great! Turns out, it is even the go to sensor for Stratux, so I went ahead and plugged it in, activated it...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday