Close

18880 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た 《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸₩셔츠룸ⓤsilverⓞ"

  • Donor Cabinet work

  • 7/29/2013: As I stated; been working on the cabinet for the Mirror universe project. I bought a couple of "project" Bally Star Treks from a fellow pinball collector out of Shertz a few years ago. These have been setting in storage for a while... and...
  • 8/30/2020 initial test powering boat

  • Today I managed to test the motor after tightening the belts considerably so they wouldn't skip teeth.  I had to hammer the pulley on the shaft to get the higher tension, so an adjustable idler pulley on each belt may may more sense in the future....
  • Early notes

  • This is retroactive notes, based on memory of this project Here is an early test (april 2019) done with the gear changer. At that point I presumed a single axis could hold the gears, but there was too much play up/down so the later design holds the gears...
  • Gear ratios

  • I'm going to label these two gears of interest the "inner" and "hour hand" gear. The hour hand gear is the one with the stem riser that winds up accepting the hour hand. The inner gear meshes on its outside edge with the minute hand shaft and on the...
  • Designing for Calibration

  • Designing parts to fit perfectly together is hard. Whether it's the coarseness of our fabrication tools or that of the vendor selling us these parts, nothing is perfect. Engineering has cute word for it: tolerances. Maybe it's me: "I can drill that hole...
  • Purchased Hardware & Electronics

  • In order to stick to my design goal of an AUD$1000 budget I decided to start a bill of materials spreadsheet. This would be a handy tool to keep track of budget and also allow me to show people if they wanted to try making something similar. Below is...
  • Measuring Magnetic Fields in a Volume

  • Let's have a look at the first test rig for measuring magnetic fields over a 3D volume.I confess that I've been thinking about this for a few weeks, and it's been a fun (and sometimes frustrating) design process. We'd like to accurately map the magnetic...
  • Putting all thogether

  • When the controller and the housing are assembled the wheels can be placed. Therefore the gears with 8 teeth (6 pcs.) and 12 teeth (2 pcs.) need to get equipped with a brass axle. A 3mm brass rod can be used for this and will stick well in to the gears....
  • Perfect pitch

  • Finally got around to generating a version where the input and output gear pitch matches the corresponding layers, aka split planets.  Here it is, with a twist.I generated the above with zero backlash allowance, just to make sure all the teeth were...
  • BitBeacon Stops Working When Outside

  • Wednesday, June 8, 2016Tested Bit outside. It appears the BitBeacon stops operating outside. Not sure why. We have used outside plenty of times. We did make a very minor modification to Bit since the early Bit demos at night, but still..... Anyways,...
  • 5/8/23

  • We settled on our spectrum design. Our 3d printer isn't big enough to fit the whole 3d box so we had to print it in two pieces. We waited to print both pieces until we decided on our final build. When we tested our servo moving across we found that the...
  • The End Game

  • The End GameA project has to have an "end game" to steal the concept from Chess. There comes a time not to "chase the rabbit down the hole".While laser cutters are very precise, they still have the same accuracy issues common to CNC mills.Accuracy versus...
  • [T] New Harmonic Drive Ideas

  • Looking at the current file, the Tile sticks out of the wall by 140mm. I think it's possible to reduce this to under 100mm. To do this, I need to design an even smaller harmonic drive, yet with high durability, low load displacement (high torsional rigidity)...