657 Results for "solder fume extractor"

ESP8266 - native switcher
Instructions from ESP8266 - native switcher
Relay modification part 1/3 (voltage regulator)Solder voltage regulator BA033. Component's pinouts:I soldered it directly to bottom of relay. Below I marked places which I used. Before soldering I scratched electronic path in places 2 and 3:To solder...

First try...
Log from SHT21 Humidity sensor board
All parts arrived and today I tried my first smt soldering at all.Here, just some photographs during the process....At first I aligned the board in between the holders made by OSH:Well, easy and I was glad to have had a small wooden board to which I...

Repairing an Anker E5 16000mAh Powerbank
Instructions from Repairing an Anker E5 16000mAh Powerbank
Inside was a nicely build pack. I thought there would be Panasonic cells inside, but this was not the case (those are green). But the cells are 3200mAh a piece.You can try to remove the batteries, but they are stuck to the bottom side with double sided...

Mount the Charging Board :
Instructions from SOLAR POWERED WIFI WEATHER STATION
Stick a small piece of double sided tap on the back side of the charging module and then paste it on the perforated board as shown in the picture.During mounting care should be taken to align the board in such a way that the soldering holes will match...

Success!
Log from LIS3DH breakout board
Finally I have a good board:After seeking for advice in a few places, this is how I soldered the LGA package:pre-tin the package's pads with an ironspread some flux gel on the PCB and place the part:I was also advised to apply some solder to the PCB...

PCBs are soldered and first tests show it's working
Log from Tiny Solar Energy Module (TSEM)
Today I have received the components from Farnell and the AEM10941 harvesting ICs from E-peas. I used a solder stencil from Elecrow, chipquik SMD291SNL10 solder paste and used an solder paste spreader from OSH Stencil, basically a credit card...

SNÖ Tip: Don’t forget your ground!
Log from Korg Volca Bass MIDI + Patchbay + USB-C + SNÖkoder
One thing these battery capable devices that are working in different voltages through the PCB, grounding your new fantastical bonanza add-on. Yeah... no comment... So, I found a good “re-use” Tip. See the lower right corner screw hole,...

Sci-fi grade Home Automation
Instructions from Sci-fi grade Home Automation
Build the base station using the following simple steps:Disassemble the outlet controller remote and throw away the plastic casingSolder wires between the +5v line on the Arduino and the positive battery terminal on the remote.Do the same with the ground...

Attach the Teensy board to the Stripboard
Instructions from Turnado Hardware MIDI Controller
Follow the following steps using the below photos as a guide: Cut a piece of stripboard to a size that has 36 strips/tracks that are 21 holes long.Cut all 36 tracks in half (making 72 individual tracks).Solder the IC socket to the stripboard at one edge...

Mutable Instruments Clouds PCB Panel
Details from Mutable Instruments Clouds PCB Panel
Original, purple Oshpark, black and white variation. The art piece is from the Hackaday.com article, Neurons a Hacker Perspective by Joe Kim. Here is Joe's talk at the Superconference about balancing art and technology. For most PCB art there are 4-5...

Assemble the microphone
Log from External mic for phone timegrapher app
Fashion a lump of something heavy into a block with a flat, smooth face. Glue a piezo transducer to the block - this one is a cheap 20mm diameter type. I've drilled and tapped a couple of screw holes in the block for later... Solder a length of screened...

Building the Battery Interface Cable for G1 Volt
Instructions from DC-DC Solar EV Charger
Solder the 40 pin female connector to the BCI2103 pcb.Cut a 6 foot piece of 25 conductor 20 awg cable. The CF5-05-25 cable has numbered wires. Remove 4 inches of sheath from one end and 6 inches from the other. At the end with 6 inches...

Assembly
Log from The fsociety Keyboard
As I probably have said on earlier log, I started this project 3-Weeks ago with no intention in mind at all to post the documentation online and let alone submitting to Hackaday Prize contest. I started posting this project from nothing just two days...

MAPone
Instructions from MAPone
NOTES:Assemble the parts in the order in which they are listed on the assembly drawing.Cap C2 is polarized - verify before solderingDiode D1 is polarized and mounted vertically - verify before soldering.LED's D2, D3 are polarized - verify before soldering.LED's...

Temperature Profile Testing
Log from T-962A Reflow Oven Modifications
Introduction Before I started to run PCBs through the oven, I wanted to characterize the behavior. I ran a series of trials where I measure the temperature at a PCB with a multimeter. That way I could compare the temperature...

|<
<
3
4
5
6
7
>
>|