86 Results for "%E3%80%8A%EC%B5%9C%EC%A0%80%EA%B0%80 O1O%CE%9E5793%CE%9E7458%E3%80%8B %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%E3%86%8B %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%85%94%EC%B8%A0%EB%A3%B8applause%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%EC%8B%A0%EC%82%AC%EC%95%84%EC%9D%B4%EB%A6%B0%EC%A3%BC%EB%8C%80caught %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%E3%8F%87%E3%85%97%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0queer"

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

Trying out GATTTOOL
Instructions from Reading a bunch of BLE sensors with raspberryZero
Now that i know how to access and decode the data lets try the Raspi GATTTOOL default BLE handler:Native to Debian and a lso to a bunch of linux distros or so i've heard of . First i reset the bluetooth of the raspi, just in case: sudo service bluetooth...

Some notes
Instructions from Hydroponics Sensor
The ESP-32 board pins operate in 3.3v levels while the Gravity pH and EC sensors operate in 5V. I inserted a simple voltage divider to shift 5v to 3.3v levels on the signal pins.

Aeroponic All-year Greenhouse on a Budged
Instructions from Aeroponic All-year Greenhouse on a Budged
Next we will prepare the water flow. I decided to use this combination of pump and tubing, because they fit without an adapter. Other combinations work also. Clear tubbing isnt the best solution, because algae will grow inside the tubes. you can prevent...

sdramThingZero - 133MS/s 32-bit Logic Analyzer
Instructions from sdramThingZero - 133MS/s 32-bit Logic Analyzer
Solder up them Address-Lines (And Clock)The core-concept behind sdramThing is that of loading (half of) the memory-locations with commands that will be (eventually) directly fed-back to the SDRAM itself. Taking into account the characteristics of SDRAM,...

Ultraviolet Lightsaber. Kill COVID-19 with Style.
Instructions from Ultraviolet Lightsaber. Kill COVID-19 with Style.
UV-C bulbs use a dab of mercury plus a glowing hot filliment in a low pressure tube of glass to generate ultraviolet light that peaks around 253.7 nano meters, the optimal germicidal wavelength in the UV-C part of the spectrum. Not to be...

Manual SMT Pick and Place Machine
Instructions from Manual SMT Pick and Place Machine
The Arduino code is incredibly simple, with some strange looking oversampling for preventing the motors from vibrating:void sampling() //Oversample the slider readings to avoid motor vibration. { i=0; val =0; smallVal=0; while(i

▇▇▇▇ Create a Testbench ▇▇▇▇
Instructions from FPGA Bootcamp #1
Before you commit your design to an FPGA, you’ll probably want to simulate it. Debugging is much easier during simulation because you can examine everything. When the Verilog simulator runs, it follows rules about timing that take into account how everything...

Instructions
Instructions from Budget DIY ESP32 GPS Base Station and Receiver
Best Budget DIY GPS/GNSS Base Station using the UM980 and a ESP32Introduction The ESP32 is a versatile microcontroller renowned for its WiFi and Bluetooth capabilities. In this guide, we’ll walk you through setting up the your ESP32 development board...

▇▇▇▇ Key Point #1: Does Verilog Execute Like Software? ▇▇▇▇
Instructions from FPGA Bootcamp #1
(Note: now we are going to start working on the Adder. You can download the source from the file section or follow along in the online simulator). Verilog isn't executable in the same way that C or Python code is (except when it is). That’s...

▇▇▇▇ Understanding Clock Division ▇▇▇▇
Instructions from FPGA Bootcamp #2
At these clock frequencies, this technique of dividing down the clock is OK, but usually you'd rather use the FPGA's clock circuitry like a PLL or DLL to generate different timings, if possible. How you do this will depend on your FPGA and won't work...

Thanks!
Instructions from Smiley TOF Module
This project would not be anywhere near as complete without some awesome online resources and some awesome people. I would like to thank the devs at Adafruit for making some incredibly useful resources. I referred to the Metro Mini and VL53L0X product...

Checking to start
Instructions from Pulse sensor to actuate a Robotic Hand
First check the you have necessary materials to make the project. You need some 3D printed parts, so a printer is necessary or at least the posibility of print. We print with protopasta carbon fiber filament but you can print in PLA, thats if you want...

Instructions
Instructions from DIY Ntrip Server and Reference Station Setup
DIY Onocoy Reference Station Setup GuideIn this guide, we’ll walk you through the process of setting up your own GPS Onocoy server using cost-effective hardware options and reliable GPS receivers. Whether you’re interested in enhancing the accuracy of...

▇▇▇▇ Counting and Dividing ▇▇▇▇
Instructions from FPGA Bootcamp #2
The remainder of the Verilog takes the 12MHz clock and uses it to drive a 16 bit counter. When the counter overflows, another counter increases. When that counter reaches 91, the secondary counter goes to zero. This takes roughly 1/2 second at 12MHz....

1
2
3
4
5
>
>|