Results for %E3%80%8A%EC%B5%9C%EC%A0%80%EA%B0%80 O1O%CE%9E5793%CE%9E7458%E3%80%8B %ED%8D%BC%EB%B8%94%EB%A6%AD%EC%97%85%EC%86%8C%EC%8B%9C%EC%8A%A4%ED%85%9C%D0%A6 %ED%8D%BC%EB%B8%94%EB%A6%AD%EB%A3%B8cathedral%ED%8D%BC%EB%B8%94%EB%A6%AD%EB%A3%B8%EA%B0%95%EB%82%A8%ED%8D%BC%EB%B8%94%EB%A6%AD%ED%8D%BC%EB%B8%94%EB%A6%AD%EC%88%A0%EC%A7%91taking %ED%8D%BC%EB%B8%94%EB%A6%AD%EC%88%A0%EC%A7%91%E2%80%B0%E3%81%BE%ED%8D%BC%EB%B8%94%EB%A6%AD%EC%88%A0%EC%A7%91located

Starfish Cat: Your Lovecraftian Furby-like Friend
Instructions from Starfish Cat: Your Lovecraftian Furby-like Friend
Plug in your Cat's nervous system. Connect the Photon to your other components. I do this by using 3x20 breakaway right angle headers where several rows have been shorted together to be power and others to be ground. This lets me better organize my components.Pin...

Understanding how to disconnect the speaker
Instructions from Hush Owlet
moThe big black device in the middle of the printed circuit board (PCB) is the speaker (aka buzzer, or transducer). You can see a little slit in the one side where the sound comes out. There is a back side to the circuit board that you cannot easily...

EDID Inserter
Instructions from EDID Inserter
Plug in the freshly minted EDID Inserter and a repeated invocation of the following should yield only 256 FFs typical of an EEPROM fresh from the factory:sudo i2cdump 3 0x50Dire admonitions are issued even when merely trying to read:No size specified...

▇▇▇▇ D Flip Flops ▇▇▇▇
Instructions from FPGA Bootcamp #0
The SR latch modified with the inverter is often called a D latch because the single input is data for the latch to store. To make it a D flip flop, though, you need to arrange to capture the data at a clock edge, not just any time the latch is enabled....

Redtree Hydra: A modular platform for robotics
Instructions from Redtree Hydra: A modular platform for robotics
Attaching a SensorIn order to attach a sensor, motor, camera or other component to the Redtree Hydra, the FPGA inside must be programmed. We know that this is normally a tricky task, so we created a tool to simplify it. The Redtree Hydra has four I/O...

Wiring the Circuit
Instructions from The Wireless Tin Can Telephone
Once everything is securely glued in, it’s time for wiring! Use the provided schematic to connect all the jumpers to their appropriate pins. I’ll also provide the pin-outs below: (Note, this is for the Gravity Expansion HAT) Antenna Board: MI -> MISOMO...

Build and flash the Libros firmware
Instructions from The Open Book
Support for the ESP32-S3 Open Book is very early at this time; there is no prebuilt firmware image, so you'll need to have both Visual Studio Code and PlatformIO installed. Download the Libros firmware from GitHub, open...

Aeroponic All-year Greenhouse on a Budged
Instructions from Aeroponic All-year Greenhouse on a Budged
Next we will prepare the water flow. I decided to use this combination of pump and tubing, because they fit without an adapter. Other combinations work also. Clear tubbing isnt the best solution, because algae will grow inside the tubes. you can prevent...

Program the Microcontroller
Instructions from Fear the Scary Cat!
Before mounting the prototype PCB to the housing, I recommend uploading the required sketch to the ATtiny84 microcontroller with a programmer of your choice. I used a USBtinyISP type shown in the picture. /*Sketch for the Scary Cat Project by Gene H*/...

Turn on and Troubleshooting Notes
Instructions from Flea-Scope USB O-scope (18 Msps, $13 BoM, WebUSB)
I first visually look for shorts/opens, especially on the QFN or QFP and USB (shorts can be easily reworked with the Kester 2331-ZX flux pen; always clean and dry boards after rework; I use isopropyl alcohol and a toothbrush followed by running water)....

Thanks!
Instructions from Smiley TOF Module
This project would not be anywhere near as complete without some awesome online resources and some awesome people. I would like to thank the devs at Adafruit for making some incredibly useful resources. I referred to the Metro Mini and VL53L0X product...

Instructions
Instructions from DIY Ntrip Server and Reference Station Setup
DIY Onocoy Reference Station Setup GuideIn this guide, we’ll walk you through the process of setting up your own GPS Onocoy server using cost-effective hardware options and reliable GPS receivers. Whether you’re interested in enhancing the accuracy of...

NODE-RED CONNECTIONS!
Instructions from OBS_IRL_STREAM_DECK
The first thing we need is a basic flow to separate button presses into different outputs. [{"id":"50b49ab2.1e6f64","type":"mqtt in","z":"7805686.aa4fd98","name":"","topic":"button_glove","qos":"0","datatype":"auto","broker":"","x":310,"y":2180,"wires":[["ea9f502f.2dd17"]]},{"id":"ea9f502f.2dd17","type":"json","z":"7805686.aa4fd98","name":"","property":"payload","action":"obj","pretty":false,"x":490,"y":2180,"wires":[["425aef92.aa3da8"]]},{"id":"425aef92.aa3da8","type":"function","z":"7805686.aa4fd98","name":"ButtonSeperator","func":"var...

Checking to start
Instructions from Pulse sensor to actuate a Robotic Hand
First check the you have necessary materials to make the project. You need some 3D printed parts, so a printer is necessary or at least the posibility of print. We print with protopasta carbon fiber filament but you can print in PLA, thats if you want...

Connections
Instructions from TRICORDUINO - 3.0 True Scientific Tricorder
You can find every information about Feather MO Adalogger in: https://learn.adafruit.com/adafruit-feather-m0-adalogger/overview I have used all pins of Feather and I would like to have more pins available. These are the connections of the set: Pin00-...