81 Results for "TTL computer"

Flash Sonoff with Micropython and connect
Instructions from Christmas Tree Automatic Watering System
Pry open case and solder on the 5 pin male header. Follow the offical docs to see details for most of the software stuff: https://docs.micropython.org/en/latest/esp8266/tutorial/intro.html On your computer, install esptool.py and download the latest...

Customize RN4677 settings.
Instructions from BTCON
You should have the Microchip RN4677 Bluetooth® 4.0 Dual Mode Module User’s Guide handy for this step. Familiarize yourself with the command syntax and how to enter/exit command mode.First connect the Rx & Tx lines to an RS232 port on a computer. ...

USB to TTL
Instructions from 8052AH-BASIC single-board computer
USB to TTL SBC connection GND GND +5V VBUS TDX RXD RXD TXD

WiFi Lawn/Garden Sprinkler Controller (ESP8266)
Instructions from WiFi Lawn/Garden Sprinkler Controller (ESP8266)
When initially powered on, the internet access point will not be setup.The ESPrinkler will therefore switch to AP mode. It will be come anaccess point in itself.So connect to ESPrinkler2_XXXXXX with a wifi enabled device (nopassword).Browse to 192.168.4.1The...

Operation
Instructions from PhotometryBox
Plug in powerConnect NI-DAQ USB-6009 to computer with USBOpen Strathclyde WinEDR software on computerNavigate to Record-->Record to diskNavigate to File-->New and set file nameYou should see live traces on the screen but NOTHING IS BEING RECORDED YETSet...

Yet another laser engraver / cutter
Instructions from Yet another laser engraver / cutter
Stepper motor driver boardI basically copied the GRBL shield or any other stepper driver board for the A4988 driver there is.I used BlackBoard 1.1 for the PCB design, neverthless the wireing is horrible ! I am not that into electronics. After a lot of...

First commissioning of the SIMATIC IOT2000
Instructions from Siemens SIMATIC IOT2000 to Ubidots + NodeRED
The following steps show how to access the SIMATIC IOT2040 using the static IP to setup the gateway's network. At this point is important to mention that the SIMATIC IOT 2040 brings DHCP Address by default in the Ethernet Port - X2P1, if your desire...

First commissioning of the SIMATIC IOT2000
Instructions from Siemens SIMATIC IOT2000 Series to Ubidots + Arduin
The following steps show how to access the SIMATIC IOT2040 using the static IP to setup the gateway's network. At this point is important to mention that the SIMATIC IOT 2040 brings DHCP Address by default in the Ethernet Port - X2P1, if your desire...

Open LIDAR
Instructions from Open LIDAR
Setting up the bluetooth moduleTools: TTL (or FTDI) cable, TinySine Bluetooth Module, computer with usb port, serial monitorFirst things first, the bluetooth module comes with a default BAUD rate of 9600. Yeah, that's not going to do. So lets speed things...

LPS Mini
Instructions from LPS Mini
Plug in the USB to TTL converter to a computer. Setup a terminal program for 115200-8-N-1 (earlier versions used 57600-8-N-1) and you will see something like this:LPSMini v1.0 SetupDIP L:1021, 0 H:510, 8:0x80DECA0130Tag addr: DECA01000 Setup done.As...

Serial communication
Instructions from ESP cookbook
After soon 60 years the RS-232 standard is doing strong, as that's what we're talking with to our most modern IoT thingys (yep I know about TTL vs positive/negative levels, pretty close anyway I'd say). Pretty much any MCU board talks RS-232 to the computer,...

Connect the screen
Instructions from Another Retropie Portable Gaming Device
and follow Adafruit’s procedure: https://learn.adafruit.com/adafruit-dpi-display-kippah-ttl-tft/installation

Connect the serial port
Instructions from OMEN Bravo
Connect the serial pins TxD, RxD and GND to the TTL-to-USB converter

Wire the sensors
Instructions from Scooter 2
I've connected the sensors as Left: TTL on D10, echo on D11Front: TTL on D8, echo on D9Right: TTL on D6, echo on D7

Step 2
Instructions from ESP8266EX Fun With Relay Module, Home Assistant & MQTT
Insert USB to TTL module in your PC and check if Windows/Linux recognize USB to TTL module. If not, download (for Windows) Silabs Direct Driver For USB to TTL.

1
2
3
4
5
>
>|