Close

1979 Results for "『 모든문의 OIO=5793=7458 』 선릉셔츠룸㈄ 『 모든문의 OIO=5793=7458 』 Ηcake²셔츠룸테란강남셔츠룸デwriter 셔츠룸테란강남셔츠룸 선릉셔츠룸⒁셔츠룸사이즈┲exhausted⅔"

  • Conclusion
  • Instructions     from Accuracy-Sensing Smart Sports Rebounder with ESP32
  • This proof of concept demonstrates that it's possible to track and log a soccer ball's landing position on a sports rebounder without using a webcam - instead, you can feed the output of several accelerometers into a trained recurrent neural network...

  • Arduino-Compatible FPGA Shield
  • Instructions     from Arduino-Compatible FPGA Shield
  • Step 3 - Build major footprints:  Costing the available board area requires building the major footprints and placing them on the PCB.  Built early footprints and placed to determine what additional space is avail.  Files in git.

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • As you can see in the picture, the screen is glued onto the PCB with a thick piece of aluminium between them. Now we have to remove the LCD screen and plate from the motherboard. This is tricky. You must be extremely careful, because the LCD is made...

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • Now is a good time to test your LCD and make sure it still works. Load the batteries back into the back half of the case. Press the motherboard against the back half of the case so the battery connectors make contact. Use a screwdriver or some other...

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • Assemble your LCD sandwich with the EL panel on the back, then the polarizer, then the glass. You can use some scotch tape around the edge to hold everything in place. I used some putty to stick the whole thing to the PCB, but you could also use some...

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • Carefully bend the EL panel leads so they fold around the back of the PCB. The panel can bend pretty far, just don't crease it.Now install the board back in the front half of the case and screw it down. The EL panel leads will stick up through gap between...

  • EFFECTIVE STUN GUN

  • Instructions     from EFFECTIVE STUN GUN
  • CLEAN UP YOUR WORKSPACEGather your componentsWe will start with the "multivibrator" or "Oscillator" circuit. It supplies an A.C. Waveform to the "T1" transformer. you can make a PCB or just solder the legs togetherIt's not a very complex circuit.First...

  • CANPi
  • Instructions     from CANPi
  • Get the PCB: http://oshpark.com/shared_projects/20v7dQka

  • RF light switch
  • Instructions     from RF light switch
  • If you do try this however and end up with a nice PCB and case for the transmitter and/or receiver, gimme a shout, I'd like to see pics! I'm dismanteling mine now for a house move. For the new house I will buy a kit from dx, but this was a fun learning...

  • Animatronic Iron Man MKIII suit
  • Instructions     from Animatronic Iron Man MKIII suit
  • Notes about tools and materials used:ProPoxy 20 is awesome stuff. When making the brass tube pivots for the shoulder rocket pods it was easiest to glue the brass tube to the servo casing with superglue ( I use Gorilla glue with a spray accelerator) and...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday