Close

3515 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기ð νeveningм셔츠룸후기선릉셔츠룸Ξthreshold 강남셔츠룸셔츠룸추천 셔츠룸후기シ셔츠룸후기㎩regular≡"

  • Stitch the Fabric onto the Glove

  • I stitched all the sensor pads in with regular thread, and sewed some of the cabling as well. This helps with repeated bending of the solder joint. The sensor that is closest to your thumb is where your middle finger ends, while snapping.
  • calibration screen mode (coming soon)

  • The cherry on top of the cake would definitely be a calibration screen mode. Imagine, the transparent plastic cover is off and you push a small calibration push-button. The regular screen statistics disappear and you get a full 32x24 pixels thermal camera...
  • Screw 0.75in conduit to swivel

  • After drilling the holes, you can slide the conduit onto the swivel. Once you slide the conduit onto the two bolts, slide a washer and screw a nut onto each one. These can either be lock nuts or regular nuts. Since I screw and unscrew them a lot, I used...
  • VR Tracker

  • Behind the curtains : calculating 3D position by image resectionningThe system uses OpenCV to calculate the 3D position form multiples 2D positions.First a calibration sequence is required. The calibration consists of recording some 2D positions with...
  • Preparing the Enclosure

  • Screw the hex standoffs into the Raspberry Pi and position it on the lid. You may need to file a notch in the lip of the lid for the SD card so it doesn't get snapped off. Mix some two-part epoxy and put a blob on the bottom of each standoff, press the...
  • i♥Me4e

  • The first step is to take some old sock(s) out of a drawer and start thinking about the design of the plucheThe one thing we gotta take in account is the size of the socks we're using: for an SD style, use short ones, else use regular onesOnce this is...
  • Floating, Bamboo Makerspace

  • Tying Wood (Ba'at)Most of the boats are made just by tying things together REALLY TIGHTLY. They call this process "Ba'at" in Visayan.To do this just follow these steps:Get a long piece of nylon cord (or tire rubber, or string)Tie one end around some...
  • Garage Door Sensor

  • Flash it Connect the microcontroller to your computer using a microUSB cable. Download and open GarageDoorSensor.ino. Replace the values at the top of the file with your own WiFi network info, MQTT server config, etc. For the distance threshold, choose...
  • 3D Printing

  • Because this was something I wanted to use on a regular basis, the watch needed to look polished and not super DIY. That's why I had the watch body profesionally 3D printed. If you have access to a 3D printer with great resolution and strong materials...
  • How to build it

  • If you want to build this for yourself and wonder where I buy the servos, electronics and heat shrink film from, here's the link:  https://www.aliexpress.com/store/1183027?spm=a2g0s.9042647.0.0.22234c4dK15pED https://www.youtube.com/watch?v=X6wb0cdJtoM...
  • Bored No More

  • Button Board LayoutThe layout of the button board had to be determined before I bought the wood.  Measure the big buttons and add a little wiggle room.  I chose a simple straight line of buttons but there are endless combinations you can consider. ...
  • Electric Carving Knife Hack!

  • Connecting Dildos Cut into it If you have a regular silicone dildo lying around (We have MANY), cut a slot in the back, and stick the attachment into it. Using existing holes Lots of toys have existing holes in the back for putting in a bullet vibe....
  • Choosing Components

  • There are four main parts of the circuit board. We have the atmega328p microprocessor. This is the same as is found in popular arduino models. This is the brain and will communicate with a real time clock (RTC) module, process the time, and display...