603 Results for "∇ 최저가 Ò1Ò《⑤⑦93》74⑸⑻ ∇ 셔츠룸가격ю 셔츠방수위offer셔츠룸셔츠룸셔츠룸인사readable 셔츠룸혼자ъ や셔츠룸인사셔츠룸혼자govern"

Configuring the Pixhawk to Correctly Run the Motors
Instructions from Project Albatross
Once the ASV was built, the next main step was to configure the Pixhawk for our application. As the Pixhawk would be autonomously controlling the ASV, it would act as a Rover styled robot. Therefore, we downloaded ArduRover firmware to the Pixhawk and...

I2C Sensors and debugging
Instructions from Stratux ADSB Receiver and AHRS
I wanted to use a BMP280 I had in my parts bin for altitude measurements. I have used it in the past for a simple weather station and it works great! Turns out, it is even the go to sensor for Stratux, so I went ahead and plugged it in, activated it...

Breathing Detection
Instructions from Breathing Detection
Labview and Arduino IntroductionLabVIEW (short for Laboratory Virtual Instrument Engineering Workbench) is a system-design platform and development environment for a visual programming language from National Instruments.To learn about LabView check official...

DIY SlingBox $30
Instructions from DIY SlingBox $30
#!/bin/bash##recording1.shirsend SEND_ONCE --count=2 radioshack BTN_4irsend SEND_ONCE --count=2 radioshack BTN_6mencoder tv:// -tv driver=v4l2:norm=NTSC_M:width=720:height=480:outfmt=uyvy:device=/dev/video0:input=0:fps=25:buffersize=16:alsa:amode=1:forcechan=2:audiorate=48000:adevice=plughw.1,0:forceaudio:immediatemode=0...

Setting up Linux AVR and ARM toolchains
Instructions from Setting up Linux AVR and ARM toolchains
INSTALLING MINT ON A RELUCTANT TOSHIBA SATELLITE LAPTOPDownloaded the latest Linux Mint 16 with Mate image via torrent from linuxmint.org. Burned to DVD and used it to boot the Toshiba. All seemed to be going well untill the boot finished and I tried...

Smart Solder reflow oven
Instructions from Smart Solder reflow oven
First thing to do is create simple heater controller. My idea is to use PWM signal what will turn on/of heating element, and because PWM is running more than 1kHz, i can get very fine power control. Here is original circuit:Idea very simple. First i...

Futurama's Jack dispenser
Instructions from Futurama's Jack dispenser
In order to add wireless access point capability to your media server, you need to install hostapd (hostapd_8192cu from AUR if your wifi dongle is based on a rtl8192cu chipset) and dhcp. If you have installed yaourt as stated in an upper Build Instruction,...

B(h)ackpack AP
Instructions from B(h)ackpack AP
These directions will only get you as far as I've come. If you have any ideas for step 9, please consider becoming a collaborator for this project.Obtain Raspberry Pi 2 (or better).Install Raspbian.Obtain a powered USB hub to connect the following components...

Back To The Future Time Circuit Clock
Instructions from Back To The Future Time Circuit Clock
Solder display PCBs to display driver PCBs using angular pin headers and in case of 14-segments, an additional ribbon cable connection is required.

Back To The Future Time Circuit Clock
Instructions from Back To The Future Time Circuit Clock
Connect driver boards with ribbon cables. 7-segment display boards and led board uses 10 wire cable, 14-segment displays use 12 wire cables.Note that there is no 12 wire IDC plug, so I used 14 wire plug and left the last two wires unconnected on the...

650nm 5mw Laser Build
Instructions from 650nm 5mw Laser Build
After some scrounging around I found a cheap axis laser housing with diode and driver board still intact! For me, this is a mirracle as most of the time, I usually disassemble things when I first get them.After I scrounged up the rest of the parts I...

ramanPi - Raman Spectrometer
Instructions from ramanPi - Raman Spectrometer
Below is a list of build instruction logs that will instruct you on how to go all the way from sourcing your components to printing the parts, and constructing your very own raman spectrometer!To begin, you will need some tools.. Pretty much every...

open-Spectrometer
Instructions from open-Spectrometer
Ensure the FTDI virtual COM port driver is installed. Ensure Python is installed. Download or clone the open-spectrometer github repository. Copy the contents of the directory desktop-software into your Python installation's site-packages directory (you...

Open Source Science Tricorder
Instructions from Open Source Science Tricorder
Step 1: Motherboard Assembly and ProgrammingI designed all of the boards to be hand solder friendly, with leadless QFNs all on one side (that can be reflowed). If the other side has components, these are usually larger and easier to hand solder. Step...

Daisy Kite Airborne Wind Turbine
Instructions from Daisy Kite Airborne Wind Turbine
Read over this system design note...Daisy Project System DesignIntroductionThe Daisy project is an attempt to realize competitive open source airborne wind energy generation.Project Executive SummaryThe Daisy project is part of the rapid AWE development...

1
2
3
4
5
>
>|