546 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 쓰리아워⒮ 강남쓰리아워sentence쓰리아워㈗쓰리아워레깅스룸doubtful 강남쓰리아워Α강남술집정보и강남술집정보ㆆ♬쓰리아워these"

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

Cree Dimming Level
Instructions from Cree Dimming Level
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

The supports/bearings
Instructions from Projector Screen
Drill two holes, almost all the way through, two blocks of something the same size as the outer diameter of your roller blade bearings. It's a common size like 3/4 or 7/8in. Make them identical. For the hole you are after, you need a nut on the threaded...

Animatronic AVP Predator cannon
Instructions from Animatronic AVP Predator cannon
Cannon code- #include "Servo.h" // include the servo library Servo armServo; // servo to raise the arm Servo cannonServo; // servo to recoil cannon // these constants won't change: const int triggerSensor = 1; // the sensor is connected to analog pin...

Paperclip Chainmaille
Instructions from Paperclip Chainmaille
2.) Wrap the paperclip very tightly around a small, 1/8 inch diameter rod or screwdriver.

Experiment Bioroid!
Instructions from Experiment Bioroid!
By using "Dremel circle cutter" cut two plastic circles177mm Diameter for pressure sensitive surface155mm Diameter for bottom baseIn my case I build my own circle cuttercheck video for details https://www.youtube.com/watch?v=D8kZFAhsS1g

Jewel Box Servo Meter
Instructions from Jewel Box Servo Meter
Bend the pins on the header at a right angle. Drill 8 holes 1/16-inch (1.6mm) diameter in a line spaced 0.1-inch (2.54mm) on centers. Pass the pins through the holes with the header on the underside of the box.

ChipWhisperer®: Security Research
Instructions from ChipWhisperer®: Security Research
Optional (see #6 too, option of hard or soft enclosure): Use a 12" piece of 3" clear diameter heat shrink tubing to cover the board, the cut out the USB-mini connector with an X-acto knife, and mount rubber bumpers such as Digikey part # SJ5748-0-ND...

Low Cost CO2 Laser Build
Instructions from Low Cost CO2 Laser Build
Mirror Mounts0Mirror Mounts… where to begin, in many ways… these are the make or break it for this project. These have some very high tolerances and requirments. Especially considering I am doing this all by hand, after all, the goal of this project...

A 25 cent Phone to Microscope Adapter
Instructions from A 25 cent Phone to Microscope Adapter
To hold the iPhone into the foam block, I routed a pocket the same size as theiPhone into the top of the block. Normally, I would have routed the holea little bit larger than the phone to ensure that it would fit, but by making the pocket the same size,...

FireCoates
Instructions from FireCoates
Optional 3D Printed Jacket Module CaseDownload the Base and Top to the case and print them on your favorite RepRap OpenSource 3D Printer. It should come out looking similar to this(colors may vary ;) ):The headphone jack hole may need to be cleaned up...

TS9 to F connector
Instructions from TS9 to F connector
Cut off a short section of RG-59 cable. Strip both ends so you are left with the center conductor, an inch of exposed wire on one end, and 3/8in on the other. Rotate it between your fingers and sand down the remaining foam insulation so it...

Goliath - A Gas Powered Quadcopter
Instructions from Goliath - A Gas Powered Quadcopter
Building the ExhaustTools: Chop Saw or Reciprocating Saw, Files, Welder, Torx (T40) bit, Socket Wrench, 1/4" and 7/16" socketsA) Cut the materialsUsing the chop saw or reciprocating saw, cut the 1" diameter U-Turn and the 135 Bend, as well as the 1 1/8"...

ramanPi - Raman Spectrometer
Instructions from ramanPi - Raman Spectrometer
Below is a list of build instruction logs that will instruct you on how to go all the way from sourcing your components to printing the parts, and constructing your very own raman spectrometer!To begin, you will need some tools.. Pretty much every...

ATX Benchtop Power Supply
Instructions from ATX Benchtop Power Supply
Get some help from the Internet to determine how much current your wires can handle. That will dictate how many of each color wire you'll need to run to each binding post. I threw in an extra wire or two for good measure; in my case, the 12v and 5v lines...

1
2
3
4
5
>
>|