5497 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Building the AUV - Internal
Instructions from Project Albatross
The internals of the AUV performed the heavy work of actually taking water quality measurements and controlling the submersible's buoyancy. Evidently, it also required a sophisticated mechanical design to fit the necessary components into the confined...

PIR Sensor with Push Notifications to Smartphone
Instructions from PIR Sensor with Push Notifications to Smartphone
Wire everything up (See tutorials in 433utils/wiringPi) tl;dr data to pin 2, and then vcc and gnd.

Mandalorian Infiltration Vambrace
Instructions from Mandalorian Infiltration Vambrace
Step 2: Order some stuff. Find the shopping list above in the components section and purchase everything from Amazon, Harbor freight, or your local Walmart.

Meteor Hunter
Instructions from Meteor Hunter
Once you have everything hooked up make sure you have python 2.7 installed and OpenCV (here).

9
Instructions from Harmonic Gear Driven Star Tracker
insert motor (with motor mount and oval drive installed) mount onto stage 1 and bolt everything together with 4x M3x60 bolts and 4x M3 nuts

Time to solder everything!
Instructions from Meditation Audio Pod
If you're happy with the whole experience (i.e. wires are long enough, response time is good, speakers stay on for how long you want, etc) it's time to connect everything together! I find soldering a lot of fun so it's one of my favourite parts...

1Charger
Instructions from 1Charger
Time to think inside the box...1. Flash ATtiny without CALIBRATION defined ( see step 4 )2. Verify everything works as expected3. Assemble project box and solder connectors.\(^_^)/ DONE !

Variable bench powersupply 1-80V 0-10A
Instructions from Variable bench powersupply 1-80V 0-10A
Create frontplate+ top plate + backplate from sheetmaterial. Also make the bottom plate (I used 8mm multiplex). Make shure you have enough room for everything. I made the top and bottom plates too long so I can cut them off later.

Solarmodule preparation
Instructions from I<3T
Carefully put solar module on some soft underground so the front does not scratch. Then cut the long wire to around 50cm (see backside image as reference). Everything will be put in the back of the panel and there is plenty of room.

Assembly
Instructions from Exhaust Fan Controller for Range Hood
Solder the sensors to a foot or 2 of wire and run them through the wiring hole in the sensor enclosure. After you’ve mounted the relay shield into the enclosure, connect everything up to the screw terminals as-labeled. It should look something like this...

Single Chip AVR BASIC Computer
Instructions from Single Chip AVR BASIC Computer
Completed PCB: Once I had all the components and had received the PCB, I assembled it and carried out some basic multimeter tests ensuring no short circuits were present (mainly ensuring no pins had shorts to the ground plane). No issues were present...

Try out your new wireless keyboard
Instructions from Wireless BLE Kinesis Advantage Keyboard (USB Host)
After uploading and plugging back your nRF52 feather, it should show up as a bluetooth keyboard, ready to be paired. Pair your keyboard from your computer's bluetooth. It should show up as "Kinesis Advantage 2" - You can change this name from NRF52Keyboard/bluetooth.cpp...

Assemble everything
Instructions from Lor's Electronic Heart
1. Cover the cell with Thread to make it bit not ugly.2. Place all the components on perf board before soldering to make sure everything fits under the board size.3. Solder NE555 ic with other passive components including the tactile switch, then solder...

Test....
Instructions from Black & Decker - Dust Buster: battery replacement
Put the battery pack back together with the motor.Careful, the motor might be switched on!Switch on the dust buster and check if it is proper running. Check if all the cells are connected well!If everything is fine, check if the charging is working.Double...

Raspberry Pi Night Vision Camera Hack
Instructions from Raspberry Pi Night Vision Camera Hack
If you’re happy that everything fits nicely, it is now time to start assembling the case using the nuts and bolts provided, securing it to your case. If you haven’t soldered the headers onto your Lisiparoi, do this first but make sure you solder them...

1
2
3
4
5
>
>|