577 Results for "solder fume extractor"

BOM, Tools and Skills Needed
Instructions from $1 PCB Christmas Tree
You will need:Necessary tools: soldering iron solder wire sandpaper flat pliers cutting pliers fine tweezersOptional (but handy) tools: Fume extractor multi-meter magnificent glassSkills: basic soldering skillsBill of materials: Components Supplier Wholesale...

Solder components
Instructions from Mouse locomotor activity tracker
Solder each pair of IR LED's and sensors to one of the single ethernet ports: red leads (+) to pin 1, black leads (ground) to pin 2, one yellow lead (sensor 1) to pin 3 and the other yellow lead (sensor 2) to pin 4. Solder a jumper wire to the corresponding...

Solder the first components
Instructions from 68020 minimal homebrew computer
Create a custom socket for the X-tal oscillator from some female pinheads.Solder the 74HC14.Solder the optional power supply.Solder the power LED/resistor.Solder the power switch / header.Solder the decoupling capacitors (100 nF) around the chips.Solder...

Solder the battery
Instructions from Funkey Zero
Solder the battery to the 2 corresponding through-holes, make sure that the polarity is correct

Solder the speaker
Instructions from GameOn
Solder the short piece of wire on the speaker and the 2 holes of the GameOn next to the speaker symbol. This can be done in the back to hide the speaker.

Solder the Headers
Instructions from SOLAR POWERED WIFI WEATHER STATION
Wemos modules come with variety of headers but you have to solder it according your requirement. For this project, 1. Solder the two male headers to the Wemos D1 pro mini board. 2. Solder a 4 pin male header to the BMP 280 module. After soldering the...

Solder on SMD Components
Instructions from Sig7Seg - controller for mechanical 7 segment
I start with the two TBD62083 chips, then the MCP23017. There should be a dot on the PCB to help with chip alignment. Next solder on the three resistors (two 47K and one 1K). If you're building the Photon PCB version, do the 2 capacitors then the...

Solder the Components
Instructions from DIY SOLAR SOLAR LAMP
It is good practice to solder the components according to their height. Solder the lesser height components first. You can follow the following steps to solder the components : 1. Push the component legs through their holes, and turn the PCB on its back....

Solder the wiring
Instructions from PAL / NTSC auto switch for PSONE LCD
Solder the wires to the PSONE PCB.3VGNDCSYNC (microcontroller input for detecting the type of signal)PAL / NOT_NTSC (output to select the timing)And solder the female header on the other side.I just left 2 spare wires for future uses.(The rigid wire...

Solder Buzzer & LED
Instructions from Turn Your Old Zapper Gun into meeting controller
Now solder the buzzer, led, and resister with each other see the below image for the circuit diagram

Solder the capacitors
Instructions from SumoRobot
The 2 green cylinders are the capacitors. On one side of the capacitor body there is a yellow/brown side with stripes. The capacitor leg with the striped side goes into the SumoBoard hole which is surrounded by a white half circle under the C1 and C2...

Solder the plow
Instructions from SumoRobot
Break off the plow part of the SumoBoard and clean the mouse bites with pliers. Then find the brackets and unscrew the bolts from them. Place the brackets under the SumoRobot to connect the plow and the 2 parts of the SumoBoard.Put in the bolts and screw...

Solder everything together
Instructions from Reimagining Duo Pop
1. Use the reference picture and wiring diagrams below to solder all the pieces. Your finish product may not look like mine and that is okay. Wire it in the most convenient method. I measured each wire cut and stripped the ends and then soldered them...

Solder the push button
Instructions from SumoRobot
Put the push button in the SW1 labeled holes. The polarity is important again, check the sides of the button, they should match with the drawing on the SumoBoard. There are 2 rectangles and a single rectangle, they should match with the ones on the push...

Solder on the Headers
Instructions from Autonomous Agri-robot Control System
The headers for the Nanos, compass, Ublox, Emic TFT and SIM800 are all standard male - female 0.1" pitch and are relatively easy to solder - so do these first. The main 2 MCUs push onto the underside of the PCB and the headers for the MEGA 2560...

1
2
3
4
5
>
>|