Close

173 Results for "『 모든문의 OIO=5793=7458 』 선릉셔츠룸㈄ 『 모든문의 OIO=5793=7458 』 Ηcake²셔츠룸테란강남셔츠룸デwriter 셔츠룸테란강남셔츠룸 선릉셔츠룸⒁셔츠룸사이즈┲exhausted⅔"

  • EDID Inserter
  • Instructions     from EDID Inserter
  • Besides a special build of PowerStrip (for Windows) available upon request only,some rare EDID-writing code is still archived online but never made it into mainline due to the serious risk of picking the wrong EEPROM:If you wipe the one on a DVIADD card,...

  • Authentic Blueprints
  • Instructions     from Authentic Blueprints
  • Don Your Lab Coat and Rubber Gloves...because it is now time for science! Mix equal parts of solutions A and B. You will not need much. I found about 5ml of each to be just enough for a full page. Spread the solution evenly over a sheet of paper. Those...

  • Portable LED Floodlight
  • Instructions     from Portable LED Floodlight
  • Get yourself a box, and you put that stuff in the box.What I ended up doing here is mounting metal supports to the metal tripod pole. I then used lacing twine and laced the battery to those supports, the plastic bin is basically just sandwiched in there....

  • ramanPi - Raman Spectrometer
  • Instructions     from ramanPi - Raman Spectrometer
  • Section: 7A Completed Spectrometer.  A note might be made here that this spectrometer can and will function as an independant device connected to a regular PC running the ramanPi spectraCide software!  If you wanted to use it and not build...

  • Open Source Science Tricorder
  • Instructions     from Open Source Science Tricorder
  • Step 1: Motherboard Assembly and ProgrammingI designed all of the boards to be hand solder friendly, with leadless QFNs all on one side (that can be reflowed). If the other side has components, these are usually larger and easier to hand solder. Step...

  • 8-bit Jukebox
  • Instructions     from 8-bit Jukebox
  •      Assemble the case: Add a little glue to the edges of each plate (A-1 through A-5) and press fit them together. The arrows and letters on plates A-1 through A-4 should match up as shown in Image 1. You might want to use some...

  • Bored No More
  • Instructions     from Bored No More
  • Button Board LayoutThe layout of the button board had to be determined before I bought the wood.  Measure the big buttons and add a little wiggle room.  I chose a simple straight line of buttons but there are endless combinations you can consider. ...

  • Electric Carving Knife Hack!
  • Instructions     from Electric Carving Knife Hack!
  • Connecting Dildos Cut into it If you have a regular silicone dildo lying around (We have MANY), cut a slot in the back, and stick the attachment into it. Using existing holes Lots of toys have existing holes in the back for putting in a bullet vibe....

  • Nixius
  • Instructions     from Nixius
  • Solder everything together. SMD soldering isn't hard if you are afraid of that. Using solder paste and hot air will probably be faster than a regular soldering iron.

  • Cinebike Human Powered Cinema
  • Instructions     from Cinebike Human Powered Cinema
  • First, you need a bike that can be made stationary. You need some way to get the back wheel off the ground so it can spin and run the generator. Our first idea was to use a trainer stand like this one with the generator in place of the resistance wheel....

  • Cinebike Human Powered Cinema
  • Instructions     from Cinebike Human Powered Cinema
  • A strong rider can put out 60v or more from the motor, and you're going to have to drop that down before you can charge a buffer battery. This means a voltage regulator - and since the A. the potential voltage is so high, B. The potential voltage is...

  • Cinebike Human Powered Cinema
  • Instructions     from Cinebike Human Powered Cinema
  • The projector we use is the Optoma ML750. There is no better projector for this application with a more favorable wattage/lumens/size ratio. It's the size of a sandwich, pulls little enough power that it can be human pedal-powered, and provides a bright...

  • PolaPi
  • Instructions     from PolaPi
  • The Raspberry Pi SD cardIf the adafruit PiTFT screen is used, all linux software steps are described here : https://learn.adafruit.com/adafruit-pitft-28-inch-resistive-touchscreen-display-raspberry-pi/easy-install Download the wheezy SD card image and...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday