Results for %E3%80%8A%EC%B5%9C%EC%A0%80%EA%B0%80 O1O%CE%9E5793%CE%9E7458%E3%80%8B %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%E3%86%8B %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%85%94%EC%B8%A0%EB%A3%B8applause%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%EC%8B%A0%EC%82%AC%EC%95%84%EC%9D%B4%EB%A6%B0%EC%A3%BC%EB%8C%80caught %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%E3%8F%87%E3%85%97%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0queer

AIRee Pollution Clock
Instructions from AIRee
#include #ifdef __AVR__ #include #endif // Which pin on the Arduino is connected to the NeoPixels? // On a Trinket or Gemma we suggest changing this to 1 #define PIN 6 // How many NeoPixels are attached to the Arduino? #define NUMPIXELS 48 // How much...

NODE-RED CONNECTIONS!
Instructions from OBS_IRL_STREAM_DECK
The first thing we need is a basic flow to separate button presses into different outputs. [{"id":"50b49ab2.1e6f64","type":"mqtt in","z":"7805686.aa4fd98","name":"","topic":"button_glove","qos":"0","datatype":"auto","broker":"","x":310,"y":2180,"wires":[["ea9f502f.2dd17"]]},{"id":"ea9f502f.2dd17","type":"json","z":"7805686.aa4fd98","name":"","property":"payload","action":"obj","pretty":false,"x":490,"y":2180,"wires":[["425aef92.aa3da8"]]},{"id":"425aef92.aa3da8","type":"function","z":"7805686.aa4fd98","name":"ButtonSeperator","func":"var...

▇▇▇▇ State Implementation ▇▇▇▇
Instructions from FPGA Boot Camp #4: State Machines
When creating a state machine, there are two things to consider: How to represent the state you are currently in is the most obvious one. This may seem like a trivial concern, but as you'll see, there is more to it than meets the eye. The second decision...

▇▇▇▇ Understanding Basic Logic Gates ▇▇▇▇
Instructions from FPGA Bootcamp #0
Open the simulator using this link and you'll see the three fundamental logic gates that will build up just about all kinds of logic. To the left are two logic inputs and each gate has its own output. Remember, you can click on the inputs to change from...

Configure LoRa device
Instructions from Soil moisture sensor with LoRa
In HTerm or any other terminal program you see the start of the module after plugging the power supply jumper.Now you can configure the SMT100 by entering the password in HTerm (123456) and then send AT commands (Attention: Always capitalize commands...

Connecting the wires
Instructions from ZX Spectrum Expansion Port EEPROM Interface
ZX EEPROMMemrq -> oeA0-A13 -> A0-A13D0-D7 -> D0-D75v/gnd -> 5v/gndPull the eeprom we and a14 high. Connect the the zx a14 and a15 to pin 1 and 2 of the 74ls32 then pin 3 to ce pin of the eeprom. Also Connect the...

Front end assembly
Instructions from OSUG: Open-Source Underwater Glider
Place a single 608ZZ bearing in each of “Syringe_clamp_front” and “Syringe_clamp_back” On the “Syringe_clamp_back” secure the bearing in place with the “Engine_bearing_fastener” piece, 3 M3 20mm...

AM2XBee4RC
Instructions from AM2XBee4RC
Mount your hardware and solder the appropriate wires from your ADC pads, GPIO pads and other components together. Each build will most certainly be unique so use your discretion as to which component attaches to which Arduino pin. I used the following...

The Talking Microtronic Computer System Emulator
Instructions from The Talking Microtronic Computer System Emulator
Set up the hardware - the emulator main sketch shows the pin layout: // // SD+Ethernet Shield (optional) // #if defined (SDCARD) #define SDCARD_CHIP_SELECT 4 // // software serial interface for Emic 2 TTS module (optional) // #if defined (SPEECH) #define...

Main Wiring
Instructions from Capacitive Gamepad
Connect MPR121 to arudino i2c and power. On a Micro this is pins 2&3 plus VCC and GND. Flash the arduino and make sure everything works as you like. Breaking out the RST pin to a tactile switch is probably unnecessary, i've had no problem re-flashing...

Cuts required
Instructions from The Learner's Heliostat
The plywood product I used was 1/2x2x4 G1S, $37 ea before tax in Ontario in summer of 2022. For the project infrastructure, four 1" x 4" x 8' knotty pine planks would be price competitive and less work to waterproof, but less convenient to transport....

Arduino Code
Instructions from OBS_IRL_STREAM_DECK
It's in the GITHUB! The code comes down the these smaller steps: MQTT handling and Button handling. Let's do button handling first. I made a simple button object with the pin number, button press boolean, and button count. struct Button { const uint8_t...

▇▇▇▇ D Flip Flops ▇▇▇▇
Instructions from FPGA Bootcamp #0
The SR latch modified with the inverter is often called a D latch because the single input is data for the latch to store. To make it a D flip flop, though, you need to arrange to capture the data at a clock edge, not just any time the latch is enabled....

Code for single Esp32 Board
Instructions from Bluetooth Tracker
This is the code for everything on a single Esp32 Board. Since I didn't have the correct board, I needed to use two of them, and they communicate through the serial port.The Bluetooth packets address and raw data get printed to the Arduino Serial...

HariFun#132 Sixteen Channel WiFi Remote
Instructions from HariFun#132 Sixteen Channel WiFi Remote
=== WebServer Sketch ===// PCF8574 WebServer, listens for /inline?state= // Hari Wiguna, 2016 #include #include #include #include // Declare and set these two variables here or in an include file //const byte credentialCount = 2; //IMPORTANT! Change...