14756 Results for "∇ 최저가 Ò1Ò《⑤⑦93》74⑸⑻ ∇아테나주대∃셔츠룸아테나prominently아테나셔츠룸아테나주대강남아테나셔츠룸chiefly 아테나주대Ι ｐ강남아테나셔츠룸soft"

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

74HCTxx family
Instructions from LM80C Color Computer
Choose chips of the 74HCTxx family. The "HCT" indicates a type of circuitry that is 74LS-compatible (the "LS" series was the original 74 family). The chips of the HCT series are compatible with the LS ones, because they have the same logic levels (despite...

BOM
Instructions from SimpleUI-Logger
There are approximately 40 different components and 90 parts on the PCB. The types of the components will be reduced if new version is to design. I've got most of them already in my boxes at home, after long time collection for different projects. However...

Order your parts and wait 3-4 weeks.
Instructions from 21 Band Audio Spectrum Analyzer
1. Order boards JLCPCB.com (black soldermask finish). 2. Order parts AliExpress or Amazon and for MSGEQ7 go to Mouser.com to avoid fake ICs. 3. Order LED strips from BFT-Lighting.com or whatever works for you but be consistent. Do not mix and match...

Connect the Electrodes
Instructions from Water Purification Coagulator Kit & STEM Program
Follow along with the video here. Remove the original mason jar sealing lid and ring.Put the 3D printer lid on top of the mason jar (lid shapes may vary). Connect the alligator clips to each electrode. Slide the two aluminum electrodes through...

Cree Dimming Level
Instructions from Cree Dimming Level
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

FPGA + 3 R + 1 C = MW and SW SDR Receiver
Instructions from FPGA + 3 R + 1 C = MW and SW SDR Receiver
GitHub hosts the complete project, it should be ready to synthesize and flash. Lattice Diamond 3.11 for Windows is the toolchain I used. There is a Linux version for it. Connect the secondary UART channel to pin 73 and 74 by shorting R14 and R15 on the...

PuriBottle
Instructions from PuriBottle
To make the ultrasonic sensor work, you have to read this program and create the circuit that matches with it!Here is the program:/* * created by Rui Santos, http://randomnerdtutorials.com * * Complete Guide for Ultrasonic Sensor HC-SR04 * Ultrasonic...

RPi Lego Bot 2.0
Instructions from RPi Lego Bot 2.0
Basic SetupThe OS used int htis project is Raspbian, because I'm a more familliar with debian and it already supports python and makes the GPIOs easily accessible.Download it and flash it on a SD card with 4GB or more. Plug it into your Pi and add the...

Nyan Board
Instructions from Nyan Board
Upload the following code:const int BEEP_PIN = 4; const int LED_PIN = 3; const int LENGTH = 27; const int NOTES[] = { 65, 67, 70, 67, 74, 74, 72, 65, 67, 70, 67, 72, 72, 70, 69, 67, 65, 67, 70, 67, 70, 72, 69, 65, 65, 72, 70 }; const float DURATIONS[]...

Desktop 5 Volt Blue
Instructions from Desktop 5 Volt Blue
Find an old broken USB component, such as a keyboard or mouse.Take it apart and if possible, preserve the connecters to avoid having to solder more than nessisary.Find a small plastic container, a pill bottle would likely work fine. If it's sturdy enough,...

Configuring the Pixhawk to Correctly Run the Motors
Instructions from Project Albatross
Once the ASV was built, the next main step was to configure the Pixhawk for our application. As the Pixhawk would be autonomously controlling the ASV, it would act as a Rover styled robot. Therefore, we downloaded ArduRover firmware to the Pixhawk and...

Building and printing the robot.
Instructions from DIY hobby servos quadruped robot
For building this i have made this tutorial, as there are some tricky parts. In the file section, each STL is named with the quantity of parts you need to print, if none just one needs to be printed. Also you can download files all at once at the file...

Code
Instructions from SpaceX Falcon 9R Lamp
Simply copy and paste this code into the Arduino IDE and deploy to the Arduino board. If you so wish you can mess with the RGB values for different colored flames. Supply the code with a base color value, and it will automatically choose a lighter color...

1. System Dynamics of the Ball Balancing Platform
Instructions from Adventures in state-space control, Arduino edition
Fortunately the dynamics of the table are not too complicated. Let the state, x, of the table include 2 variables, position and velocity, x and v. Given the relationship dx/dt = v, the state matrix equation is: The only way to control the position...

1
2
3
4
5
>
>|