127 Results for "C%20%EB%B0%94%EC%B9%B4%EB%9D%BC%EC%82%AC%EC%9D%B4%ED%8A%B8%EC%BF%A0%ED%8F%B0%20cddc7_com%20%E2%98%86%EB%B3%B4%EB%84%88%EC%8A%A4%EC%BD%94%EB%93%9C%20B77%E2%98%86%ED%83%9C%EC%95%88%20%EC%9B%90%EC%97%91%EC%8A%A4%EB%B2%B3%E2%91%8A%EC%9B%90%EC%A3%BC%20%EC%9B%90%EC%97%91%EC%8A%A4%EB%B2%B3%E2%94%AB%EC%95%84%EB%9E%8D%EC%B6%95%EA%B5%AC%EC%83%9D%EC%A4%91%EA%B3%84%E3%8E%97%EB%B6%80%ED%8F%89%EB%B0%94%EB%91%91%EC%9D%B4%CC%BC%EB%B0%94%EC%B9%B4%EB%9D%BC%EC%82%AC%EC%9D%B4%ED%8A%B8%EC%BF%A0%ED%8F%B0%ED%9B%84%EA%B8%B0%20soliloquist/"

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

Cree Dimming Level
Instructions from Cree Dimming Level
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

Convert the WAVE files into embedded C code
Instructions from Speaker Games
You can use this nice free software WAVToCode to convert WAVE files into a C files. Check their help page for instructions on using the software. The DAC in this module accepts only 8 or 12 bit samples but this software generates 8, 16 and 24. Load each...

Raspberry Pi Zero Smart Glass
Instructions from Raspberry Pi Zero Smart Glass
Slide the Pi Zero through the PiHolder, with curved tweezers carefully guide the jst connecter and the camera cable through Buttonholder piece and the front bridge piece.

Provisioning the Raspberry Pi
Instructions from GePS
Next, you're going to get the SD card ready for booting the operating system on the Raspberry Pi. This begins with copying the official raspbian lite image to the SD card. This is a process that can be done in many ways, and it slightly differs depending...

"Programming" Isolinear Chips
Instructions from Star Trek Shuttle Console
I really like how the Isolinear Chips turned out. They look especially neat when you hold them up to a light. I was able to print the chip labels using a brother label maker. "Programming" them is also pretty simple as you can set each Isolinear...

Address Bus
Instructions from L-Star: Software-Defined 6502 Computer
This last step is going to get REALLY tedious because the Address Bus has so many lines. But this is the last step and you should be done, so keep it up just a little longer. A0: 6502 Pin 9 to FLiP pin 13 A1: 6502 Pin 10 to FLiP pin 14 A2: 6502...

Instructions
Instructions from DIY Ntrip Server and Reference Station Setup
DIY Onocoy Reference Station Setup GuideIn this guide, we’ll walk you through the process of setting up your own GPS Onocoy server using cost-effective hardware options and reliable GPS receivers. Whether you’re interested in enhancing the accuracy of...

Step 5: Uploading Arduino Codes & Conclusion
Instructions from Spider Robot with Arduino
We have prepared a code for you so that you can move the spider robot without any problems at first. A few commands are ready in the code, but you can revise it yourself ;#include // include IR Remote library #include // include servo library //=====...

Transformer Build
Instructions from 350 Watt True Sine Inverter
This instruction is for building the transformer. It describes materials and fabrication guidance but assumes the reader has experience assembling magnetics. Additional information can be found in the magnetics zip file and the 'inductors'...

Geiger–Müller Tubes
Instructions from Cosmic Array
I've had comments regarding the validity of using Geiger–Müller Tubes for a cosmic ray (muon) detector. Pointing out that Photomultipliers and scintillation panels are best, and yes the are far more effective. However, they are also expensive,...

▇▇▇▇ D Flip Flops ▇▇▇▇
Instructions from FPGA Bootcamp #0
The SR latch modified with the inverter is often called a D latch because the single input is data for the latch to store. To make it a D flip flop, though, you need to arrange to capture the data at a clock edge, not just any time the latch is enabled....

Collect Your Parts
Instructions from Cluster Pi - Yet Another Pi Cluster Project
Parts: QuantityDescriptionLinkExt Price1SUPERMICRO CSE-502L-200B Black 1U Rackmount Mini Server Chassis 200WSuperMicro Server Chassis79.994Raspberry Pi 3B or greater140.001Mini ATX PSU II - Cool - Desktop ATX Power Supply ATX 20/24 Pin configuration...

Instructions
Instructions from Budget DIY ESP32 GPS Base Station and Receiver
Best Budget DIY GPS/GNSS Base Station using the UM980 and a ESP32Introduction The ESP32 is a versatile microcontroller renowned for its WiFi and Bluetooth capabilities. In this guide, we’ll walk you through setting up the your ESP32 development board...

CODE
Instructions from Open-Source Shallow Water Glider
The first code chunk declares the variables and establishes connections #include #include "Wire.h"#include #include "GravityTDS.h"#include #include #include "MS5837.h"#include "ping1d.h"#include "SoftwareSerial.h"#include "RTClib.h"#include //#include...

1
2
3
4
5
>
>|