Close

1380 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

  • Building the AUV - Internal
  • Instructions     from Project Albatross
  • The internals of the AUV performed the heavy work of actually taking water quality measurements and controlling the submersible's buoyancy. Evidently, it also required a sophisticated mechanical design to fit the necessary components into the confined...

  • Ultra Low Cost Electronics Kit
  • Instructions     from Ultra Low Cost Electronics Kit
  • Buy everything from the materials list from Aliexpress. Try to group your purchases under one supplier as this will lower shipping costs. Get a case that is at least 9 x 7 x 3 cm, this is just large enough for the half size breadboard.Store all components...

  • Get Everything Together
  • Instructions     from Tipo : Braille Smartphone Keypad
  • You will need: - Male to Female jumper cables - AVR programmer (  I used Pocket AVR programmer from sparkfun ) - USB micro cable for the programmer -USB OTG cable -All 3D printed parts -M3 x 10 CSK screws -Silicone button pads

  • Test the X, Y, Z motors and end stops.
  • Instructions     from DuePrint
  • If everything worked correctly you should now have control of the movement motors and end stops. Manually move the print head to the center of the printer. Next, the axes homing will be tested to ensure the motors are wired up correctly. Be prepared...

  • Bike improvement: fitting a rack
  • Instructions     from Bike improvement: fitting a rack
  • Go to the hardware store. For this project the following supplies were needed:2 x 50mm L-shaped mounting brackets1 x M6 screw, 40mm long1 x M6 washer1 x M6 locknut (it resists better to the vibrations than regular threaded nuts)2 x M5 locknuts (the rear...

  • Drilling Part I
  • Instructions     from Ender 3 PCB Drilling
  • Place the PCB to be drilled on top of a cardboard sheet (it doesn't need to be thick, mine is 1mm), which goes on top of the Ender 3 printing table. Hold everything with clamps on the corners. Alternatively, you might use double-sided stick tape.Manually...

  • The final
  • Instructions     from BrailleRAP DIY Braille embosser
  • Adjust everything, tight the needed screws and beltsAdjust the top and bottom carriage, the Braille stylus of the bottom carriageneed to slighty enter in the anvil of the top carriage.Mount the electronic board with driversWire the 12V alimentation Adjust...

  • Clock in a Box
  • Instructions     from Clock in a Box
  • The inner dimensions of the box I used: 64mm x 50mm x 44mm with roughly 8mm leeway when adding the top. I probably could have used a smaller box, but it's especially difficult to cram everything in there when including batteries and a holder. So, your...

  • Raspberry Pi Glowbe Wake Lamp
  • Instructions     from Raspberry Pi Glowbe Wake Lamp
  • We’ll run the code with cron. It should start about half an hour before you get up and probably only on weekdays. Launch the cron configuration by typing the following into a terminal: crontab -e Next, set it up by adding the following line to the end:...

  • Raspberry Pi Action Cam
  • Instructions     from Raspberry Pi Action Cam
  • I now had a pretty good idea what the final x and y dimensions were going to be. I wanted to keep the camera as close to the size of the Pi as possible, which meant the large battery had to fit snugly underneath the bottom of the Pi. I printed out a...

  • Solder everything together
  • Instructions     from Reimagining Duo Pop
  • 1. Use the reference picture and wiring diagrams below to solder all the pieces. Your finish product may not look like mine and that is okay. Wire it in the most convenient method. I measured each wire cut and stripped the ends and then soldered them...

  • Frame Cover.
  • Instructions     from The X-PC. Hackaday Prize 2022 Entry
  • Place the Frame cove face down on a flat surface. Put glue on the tabs of the back of the inner frame, then place it onto the outer cover, making sure all the tabs line up with the slots. Put more glue around the top supports and edges of the living...

  • Electronics
  • Instructions     from Galvo Laser Cutter/Engraver
  • Here is a picture of my electronics box. The parts inside are: A 12V 5A PSU, a switch for the laser, two WAGOs with 3D printed part, Arduino UNO + CNC Shield,  Galvo PSU, two galvo drivers and two converter boards. The wiring should be really straightforward....
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday