Close

864 Results for "%EA%B0%95%EB%82%A8%EC%85%94%EC%B8%A0%EB%A3%B8%E3%80%8Eoio_%EF%BC%94%EF%BC%96%EF%BC%94%EF%BC%98_%EF%BC%90%EF%BC%99%EF%BC%93%EF%BC%90%E3%80%8F%EA%B0%95%EB%82%A8%EB%A3%B8%EC%8B%B8%EB%A1%B1 %E2%88%81%EC%84%A0%EB%A6%89%EC%85%94%EC%B8%A0%EB%A3%B8%E2%88%91 %EA%B0%95%EB%82%A8%EB%9E%80%EC%A0%9C%EB%A6%AC %E2%88%80%EA%B0%95%EB%82%A8%EC%9C%A0%ED%9D%A5 %E2%88%88%EC%84%A0%EB%A6%89%EC%9C%A0%ED%9D%A5%E2%88%82 %EC%84%A0%EB%A6%89%EB%A3%B8%EC%8B%B8%EB%A1%B1%E2%88%86 %EA%B0%95%EB%82%A8%EB%A3%B8%E2%89%AE %EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E2%88%8F %EC%84%A0%EB%A6%89%EB%9E%80%EC%A0%9C%EB%A6%AC early"

  • Cree Dimming Level
  • Instructions     from Cree Dimming Level
  • Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

  • Address Bus
  • Instructions     from L-Star: Software-Defined 6502 Computer
  • This last step is going to get REALLY tedious because the Address Bus has so many lines. But this is the last step and you should be done, so keep it up just a little longer. A0: 6502 Pin 9 to FLiP pin 13 A1: 6502 Pin 10 to FLiP pin 14 A2: 6502...

  • Pedal Wiring
  • Instructions     from Pedalino™
  • Pedalino is designed to work with the majority of expression pedals on the market, but there are a few popular pedal types which are incompatible and need to use adapters in order to work with Pedalino. There is no recognized standard for footswitch...

  • AM2XBee4RC
  • Instructions     from AM2XBee4RC
  • Mount your hardware and solder the appropriate wires from your ADC pads, GPIO pads and other components together. Each build will most certainly be unique so use your discretion as to which component attaches to which Arduino pin. I used the following...

  • JeremFuge (a.k.a. LC-LE:fuge)
  • Instructions     from JeremFuge (a.k.a. LC-LE:fuge)
  • Here below are all the connections for the JeremFuge. We describe them cable per cable with each time the beginning and the end of the cable.The breadboard is welded on the Arduino Uno.Connections Breadboard : Arduino UnoA : DigitalA2 to A7 : 2 to 7...

  • Provisioning the Raspberry Pi
  • Instructions     from GePS
  • Next, you're going to get the SD card ready for booting the operating system on the Raspberry Pi. This begins with copying the official raspbian lite image to the SD card. This is a process that can be done in many ways, and it slightly differs depending...

  • Some notes
  • Instructions     from Hydroponics Sensor
  • The ESP-32 board pins operate in 3.3v levels while the Gravity pH and EC sensors operate in 5V. I inserted a simple voltage divider to shift 5v to 3.3v levels on the signal pins. 

  • Build and flash the Libros firmware
  • Instructions     from The Open Book
  • Support for the ESP32-S3 Open Book is very early at this time; there is no prebuilt firmware image, so you'll need to have both Visual Studio Code and PlatformIO installed. Download the Libros firmware from GitHub, open...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday