SLA 3D Printer HaD Super Con 2017 Badge Hacking

Description

Make a portable super small low cost 3D SLA printer with a 30mm^3 print volume out of parts laying around the house.

Details

Initial Question:

What can we do to top being rick rolled by SpriteTM

Initial Concept that stuck 3D SLA Printer.

Badge Github Repo:

https://github.com/JacobChrist/HaD-Super-Con-2017-Badge-Hacking-SLA-3D-Printer

Files

Cover Unoptimized.svg This is a first cut of a file to be used to cut the cover on Ponoko. This file should not be used to make the cover, it needs clean up, but its a place holder. To use this file the stroke width need to be set to 0.01mm and the fill needs to be removed. svg+xml - 640.54 kB - 10/22/2017 at 19:56		Download
Modified Coupler and Rod.jpg 1/4 20 threaded rod with a flat ground on one end. 1/4 20 coupling nut with taped holes for set screws JPEG Image - 48.29 kB - 10/22/2017 at 14:53	Preview	Download

Components

1 × Google Doc's for storing the BOM https://docs.google.com/spreadsheets/d/e/2PACX-1vSK38lJYoejRhkuMuIxkH8d4BwEbEV9Vad2zMkiqx6ArSiWdqNdtb4JhYfz__G4PJ0LVEFTf2GGHtA-/pubhtml
1 × 34 in.-lbs. Acetal Disc for 1/2" OD Set Screw High-Parallel-Misalignment Flexible Shaft Coupling https://www.mcmaster.com/#59985K61
1 × NEMA17 Stepper Motor http://catalog.orientalmotor.com/item/all-categories-legacy-products/tegories-pk-series-2-phase-stepping-motors-legacy-/pk243-01aa
1 × DAYLIGHT HARD RESIN https://photocentricgroup.com/usa/product/daylight-hard-resin-2/?v=7516fd43adaa

Project Logs

Collapse logs

Badge Hacking Ceremony
Jacob Christ • 11/15/2017 at 03:21 • 1 comment

We spent $700 to win $256, money well spent. Thanks Hackaday!
Mommy, Daddy?
Jacob Christ • 11/15/2017 at 02:45 • 1 comment
HaD Super Con Day 2 VLog 3 - 6
Jacob Christ • 11/12/2017 at 07:41 • 0 comments
HaD Super Con Day 2 VLog 2
Jacob Christ • 11/12/2017 at 01:00 • 0 comments
HaD Super Con Day 2 VLog 1
Jacob Christ • 11/11/2017 at 19:12 • 0 comments
We have arrived
Jacob Christ • 11/10/2017 at 22:02 • 0 comments

Just arrived to HaD Super Con and finally can fit check the badge.
Intent Reveled
Jacob Christ • 11/08/2017 at 07:07 • 0 comments

So it turns out that this is not just a super tiny SLA printer, but it a HaD badge hack super tiny SLA printer.
It's coming together.
Jacob Christ • 11/05/2017 at 18:06 • 0 comments

Jacob: Printed base overnight. I thought it was going to be difficult to get off the print bed but it was actually quite easy. Assembled and fit check all the pieces. Need to reprint the coupler to avoid interference with display board.
Need to cut the lead screw and mount the build plate. Going to turn the machine over to Mike to complete these tasks.
Build Status
Jacob Christ • 11/05/2017 at 06:24 • 0 comments

Jacob: Printed pillow block and sensor mount today, base design is almost complete, hope to kick off a print tonight.

Michael: Built light cover and build chamber (and build chamber lid). Cut guide rods to length. Tested linear slide with test pieces along with a PONTECH STP300.
Hackaday.io component list leaves something to be desired.
Jacob Christ • 11/04/2017 at 18:12 • 0 comments

Hackaday.io component list leaves something to be desired so we put the BOM into Google Doc's:

Google Doc's BOM