1545 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Glueing and soldering the WS2812B 12 LEDs ring
Instructions from (Funny) Audio spectrum by colors
Glue the ring to the plastic yellow shield. Do some attempts to set the loudspeaker on place and check that the 3 wires (DI, GND and Vcc) don't push the loudspeaker cone. To avoid any problem, I made the three 1mm holes as you can see in this picture...

The box :
Instructions from Wall-U
20X20X25 (inside) Chassis : 3.5 cm high 20cm large fold plastic and screw on the bottom Laser cut the body and assemble it. It should click into place thanks to the finger joints. Our wood wasn't perfectly flat so we had to use a few pieces of tape to...

Assemble the Box
Instructions from RPi 9000
Take the front, top, bottom, left, and right face, and form them into a box. But do not glue them together directly! Assemble everything using the sellotape first, and once everything is in place, superglue it from the inside.I used regular super glue,...

Putting It All Together
Instructions from Ariadne Headband
Now its time to program arduino, you can find arduino program in our Gitlab repository which we have linked in our project site. Next connect headband and power pin header connector, pay attention to right orientation and switch the power button. While...

Authentic Blueprints
Instructions from Authentic Blueprints
Expose the ImageLay the transparency on top of the photo paper and set it outside under a sheet of glass or acrylic. Professionals would use a UV light box (some of you may already have one for making PCBs), but 20 minutes in the California sun works...

VMware vSphere Client on Mac
Instructions from VMware vSphere Client on Mac
Run Client and Connect to Host• In Terminal navigate to the folder where the client exe is located (not the installer):cd ~/.wine/drive_c/"Program Files"/VMware/Infrastructure/"Virtual Infrastructure Client"/Launcher/• Then run the Client with this command:wine...

Clock in a Box
Instructions from Clock in a Box
The inner dimensions of the box I used: 64mm x 50mm x 44mm with roughly 8mm leeway when adding the top. I probably could have used a smaller box, but it's especially difficult to cram everything in there when including batteries and a holder. So, your...

Lasercut train points switch box
Instructions from Lasercut train points switch box
STEP 7 – ASSEMBLE DESIGNOnce the design comes through you can start to assemble your mimic. I’ve done a box here so quickly check everything fits. To fit LEDs, place LED clips through the mimic, open up the tabs with a pen so the LEDs clip into place...

Add the Soil & Plants
Instructions from Sprout: Modern Indoor Self Watering Planter
Once the cement has cured, fill the box with soil. Remember to heat seal the end of the Outlet pipe before making a hole in it for the dripper. The dripper is used to regulate the water coming out of the pipe so that the water does not flow out of the...

Exporting Multiple Bodies
Instructions from Exporting Multiple Bodies as 1 STL File-Fusion 360
Now that we’ve covered how to export a single body let’s go over how to export multiple bodies. Here’s an example of three separate bodies that are not connected to each other. The intuitive thing to do would be to select all bodies by drawing...

Install the fan into the Fan Box
Instructions from PC 140mm Air Filter
Grab your fan, fan box, fan box cover, #6 bolts, and #6 washers. Insert the fan into the fan box. Put the fan box cover on top. Add the #6 bolts and #6 washers. Tighten everything down.

Building the Badge
Instructions from DC Zia 30-in-One Badge
Building the badge is overall pretty simple. The first step is to just get everything unpacked. Included, you should have:Two DCZia stickersA CdS cell in an Adafruit bagA small OLED display5 socket stripsA transformerA key switchA key capA...

Connect the webcam to your computer and run the code
Instructions from Gear selector
Once everything is assembled, upload the code to the Arduino and connect the camera to the PC. Run the three codes: the camera code, the arm code, and the serial communicator. The conveyor belt operates continuously but will only send a signal to the...

Portable LED Floodlight
Instructions from Portable LED Floodlight
Get yourself a box, and you put that stuff in the box.What I ended up doing here is mounting metal supports to the metal tripod pole. I then used lacing twine and laced the battery to those supports, the plastic bin is basically just sandwiched in there....

Electronics
Instructions from Galvo Laser Cutter/Engraver
Here is a picture of my electronics box. The parts inside are: A 12V 5A PSU, a switch for the laser, two WAGOs with 3D printed part, Arduino UNO + CNC Shield, Galvo PSU, two galvo drivers and two converter boards. The wiring should be really straightforward....

|<
<
1
2
3
4
5
>
>|